background image

Page  4

P Scale

0 - Max

The default pressure scale is unidirectional 0 to full-scale (ex: 0 - 500 PSI). Use <UP> 

or <DOWN> to toggle the setting to a bi-directional scale (ex: ± 500 PSI). The setting 

changes from "0 - Max" to "+/- Max.

<MENU> 

Press to save and advance to next menu item

3. PRESSURE SCALE

USER MENU

The User Menu can be accessed by pressing the <MENU> key at any time after the start-up mode. Note 

that the <ZERO> key function changes to an <UP> key function when a menu is active.

The system suspends operation when in the menu and holds the last pressure value as the output value. 

If the User Menu is not active for 5 minutes (no key press), then the menu will exit and the device returns 

to normal operation.

The User Menu operation and parameters are explained below.

Output

0-5 Vdc

This item only appears if the PCB jumper is in the VOLT position. Use <UP> or 

<DOWN> to set the output signal type to 0-5 or 0-10 Vdc. The factory default is 0-5 

Vdc.

<MENU> 

Press to save and advance to next menu item

1. OUTPUT

P. Range

500 PSI

The pressure range defaults to the largest range (1) of the device. Use <UP> or

 <DOWN> to step through the four available ranges specific to the model. Available 

options are shown below in Figure 12:

2. PRESSURE RANGE

Model

1

2

3

4

01

50 PSI

25 PSI

10 PSI

5 PSI

02

100 PSI

50 PSI

20 PSI

10 PSI

03

250 PSI

125 PSI

50 PSI

25 PSI

04

500 PSI

250 PSI

100 PSI

50 PSI

05

5.0 Bar

2.5 Bar

1.0 Bar

0.5 Bar

06

7.0 Bar

3.5 Bar

1.4 Bar

0.7 Bar

07

10 Bar

5 Bar

2 Bar

1 Bar

08

35 Bar

17.5 Bar

7 Bar

3.5 Bar

09

500 kPa

250 kPa

100 kPa

50 kPa

10

700 kPa

350 kPa

140 kPa

70 kPa

11

1000 kPa

500 kPa

200 kPa

100 kPa

12

3500 kPa

1750 kPa

700 kPa

350 kPa

PRESSURE RANGE

<MENU> 

Press to save and advance to next menu item

Damping

4 sec

The pressure averaging time for surge damping defaults to 4 seconds. This can be 

changed from 1 to 60 seconds using <UP> or <DOWN>.

<MENU> 

Press to save and advance to next menu item

4. DAMPING

Figure 12

<MENU> 

Press and release the <MENU> key to enter the User Menu

IN-GE-DPXXX-02-02      11/19

Copyright © Greystone Energy Systems, Inc.   All Rights Reserved    Phone:  +1 506 853 3057  Web: www.greystoneenergy.com

Содержание DP Series







Отзывы: