background image

H40.0.01.6C-09 

Operating Manual GMH 3330 

Page 3 of 16

 

 

General Note 

Read this document carefully and get used to the operation of the device before you use it. Keep this 
document within easy reach near the device for consulting in case of doubt. 
 
The manufacturer is not liable for misprints.  

2  Safety  

2.1  Intended Use 

The safety requirements (see below) have to be observed. 
The device must be used only according to its intended purpose and under suitable conditions. 
Treat device and sensor carefully. Use only in accordance with above specification. (do not throw, hit 
against etc.). Protect plug and socket from soiling.  

The device combined with the combined measuring probe TFS 0100 is designed for room climate meas-
urements. This includes gauging of atmospheric humidity, temperature, dew point, dew point distance and 
enthalpy. 

Together with the flow rate measuring probes STS 005 and STS 020 the device provides flow rate meas-
urements either in water or in air. 

 

2.2  Safety signs and symbols 

Warnings are labelled in this document with the followings signs: 
 

 

DANGER 

        

Caution! 

This symbol warns of imminent danger, death, serious injuries 

and significant damage to property at non-observance.

 

 

Attention! 

This symbol warns of possible dangers or dangerous situa-

tions which can provoke damage to the device or environment at non-
observance.

 

 

Note!

 

This symbol point out processes which can indirectly influence 

operation or provoke unforeseen reactions at non-observance.

 

 
 

 

Содержание GMH 3330

















Отзывы: