background image

H40.0.01.6C-09 

Operating Manual GMH 3330 

Page 13 of 16

 

 

10.2  System and Error Messages  

System or error 
messages 

Description / Reason 

Remedy 

 

no probe/sensor connected 

connect probe/sensor 

probe/sensor damaged 

probe/sensor defective 

 return to manufacturer for 

repair 

 

Low battery voltage, device will 
only continue operation for a short 
time 

replace battery 

 

Low battery voltage 

replace battery 

If mains operation: wrong voltage 

replace power supply, if fault continues to exist: device 
damaged 

No display 

or 

mazy characters

 

Battery voltage too low 

replace battery 

If mains op.: power supply defec-
tive or wrong voltage/polarity 

check/replace power supply 

System error 

disconnect battery or power supply, wait for a short time, 
re-connect 

device defective 

return to manufacturer for repair 

 

Values exceeding measuring  
range 

Check: are there any values exceeding the measuring 
range specified? ->meas. value too high 

Sensor/cable defective 

-> replace 

 

Values below measuring range 

check: are there any values below the measuring 
range specified? ->meas. value too low 

Sensor/cable defective 

-> replace 

 

System fault 

switch on again: if fault continues to exist, device is 
damaged 
-> return to manufacturer for repair 

Instrument not within working tem-
perature 

keep working temperature in between -25...50°C 

 

No probe/sensor existing  
or probe/sensor defective 

connect probe/sensor; 
probe/sensor damaged -> return to manufacturer for 
repair 

 

Value cannot be calculated 

One measuring variable required for calculation is miss-
ing (no sensor) or incorrect (overflow/underflow) 

 

10.3  System and Error Messages during TFS0100 Calibration  

Error or system 
messages 

Description / Reason 

Description / Reason 

 

Deviation to high (zero point) 

correct humidity variable? 
no -> probe no longer within permissible tolerances, 
return to manufacturer for recalibration. 

 

Difference point1-point2 too small 

difference has to be at least 40% if values are entered 
manually select suitable  

 

Incorrect temperature 

calibration is only permissible in the temp. range from 
5 ... 40°C 

m b a r

m b a r

m b a r

m b a r

Содержание GMH 3330

















Отзывы: