GreenWorks Tools 21227, Руководство пользователя

Страница: 5 / 41

English
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorised Service Centre.
CHARGER AND BATTERY PACK
29697/29807- 24V 43Wh Lithium battery pack
29837- 24V 86Wh Lithium battery pack
29817/29827- 24V charger
BATTERY PACK REMOVAL AND PREPARATION FOR
RECYCLING
Contact customer service for the latest replacement parts
and accessories.
WARNING
Upon removal, cover the battery pack’s terminals with
heavy-duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its
components. Lithium-ion and nickel-cadmium batteries
must be recycled or disposed of properly. Also, never
touch both terminals with metal objects and/or body
parts as short circuit may result. Keep away from
children. Failure to comply with these warnings could
■ Install the new spool so that the cutting line and slot
align with the eyelet in the cutting head. Thread the
cutting line into the eyelet.
■ Pull the cutting line extending from the cutting head
so the cutting line releases from the slot in the spool.
■ Reinstall the spool cover by depressing tabs into slots
and pushing down until spool cover clicks into place.
CUTTING LINE REPLACEMENT
See Figures 12 - 13.
■ Remove the battery pack.
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
SPOOL REPLACEMENT
See Figure 12.
Use original manufacturer’s replacement cutting line for
best performance.
■ Remove the battery pack.
■ Push in tabs on side of spool cover.
■ Pull spool cover up to remove.
■ Remove the old spool.
■ To install the new spool, make sure the cutting line is
captured in the slot on the new spool. Make sure the
end of the cutting line is extended approximately 15cm
beyond the slot.
65
■ Remove the spool from the cutting head.
NOTE:
Remove any old cutting line remaining on the
spool.
■ Cut a piece of cutting line approximately 3m long. Use
only 1.65mm diameter monofilament cutting line.
■ Insert the cutting line into the anchor hole in the upper
part of the spool. Wind the cutting line around the upper
part of the spool clockwise, as shown by the arrows on
the spool. Place cutting line in the slot on upper spool
flange, leaving about 15cm. extended beyond the slot.
Do not overfill. After winding the cutting line, there
should be at least 0.635 cm between the wound
■ Replace the spool, and the spool cover. Refer to spool
replacement earlier in this manual.
STORING THE TRIMMER
■ Remove the battery pack from the trimmer before
storing.
cutting line and the outside edge of the spool.
■ Clean all foreign material from the trimmer.
■ Store it in a place that is inaccessible to children.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery pack life.
■ Never store batteries in a discharged condition. Wait
for battery pack to cool and fully charge immediately.
■ Store the battery pack where the temperature is below
27˚C and away from moisture.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your unit for long periods of time without using
it, recharge the batteries every month or two. This
practice will prolong battery pack life.