Greenlee GATOR CK12ID Скачать руководство пользователя страница 3

CK12ID Dieless Crimping Tool

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY 

ALERT 

SYMBOL

This symbol is used to call your attention to hazards 

or unsafe practices which could result in an injury or 

property damage. The signal word, defined below, 

indicates the severity of the hazard. The message 

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result 

in severe injury or death.

Hazards which, if not avoided, COULD result in 

severe injury or death.

Hazards or unsafe practices which, if not avoided, 

MAY result in injury or property damage.

Read and understand all of the 

instructions and safety information  

in this manual before operating or 

servicing this tool.
Failure to observe this warning will 

result in severe injury or death.

Do not use this tool in a hazard-

ous environment. Hazards include 

flammable liquids, gases, or other 

materials. Using this crimping tool in 

a hazardous environment can result  

in a fire or explosion.
Failure to observe this warning will 

result in severe injury or death.

Electric shock hazard:
This tool is not insulated. When 

using this unit on or near energized 

electrical lines, use proper personal 

protective equipment.
Failure to observe this warning 

could result in severe injury or death.

Electric shock hazard:

Connect the power cord to a 

receptacle of proper voltage for  

the tool in use on a ground fault-

protected circuit only.
Do not modify the power cord or 

plug.
Inspect the power cord before 

use. Repair or replace the cord if 

damaged.
Do not pull or carry by cord, use 

the cord as a handle, close a door 

on the cord, run over the cord, or 

pull the cord around sharp edges 

or corners. Keep the cord away 

from heated surfaces.
Do not unplug by pulling on the 

cord. To unplug, grasp and pull  

the plug—not the cord.
Disconnect from power before 

servicing.

Failure to observe these warnings 

could result in severe injury or death.

Do not expose to rain.
Do not use in wet or damp 

 locations.

Failure to observe these warnings 

could result in severe injury or death.


Содержание GATOR CK12ID























Отзывы: