background image

Table 1 lists and describes all of the BACnet data points associated with the controller inside the actuator of BACnet 
enabled AMD-TD series dampers.

Name

Type

#

Access

Description

Greenheck AMD-TD

AI

1

C

Displays the application version

AirflowSetpoint

AI

2

C

Displays the real-time setpoint in cfm

CurrentAirflow

AI

3

C

Displays the real-time volumetric airflow rate in cfm

AirVelocity

AI

4

C

Displays the real-time air velocity in fpm

DamperPosition

AI

5

C

Displays the real-time damper position as a percentage (0% - fully 
closed; 100% fully open)

MaxCFMSetpoint

AI

6

C

Displays the maximum volumetric airflow rate in cfm.  This value is 
a function of the value selected for "Maximum FPM".  (Max CFM 
Setpoint = Damper Area * Maximum FPM). 

DamperArea

AV

1

C

Represents the nominal damper face area in square feet.  Set by 
the factory.

MinimumFPMSetpoint

AV

2

C

Represents the minimum allowable velocity setpoint in fpm.  If the 
actuator receives a setpoint below the "Minimum FPM Setpoint" 
the setpoint will be set to zero.  The factory default value is 100 
fpm.   

BACnet Setpoint

AV

3

C

When the Setpoint Source is set to BACnet this variable 
establishes the unit's setpoint.  When the Damper Mode is set 
to Flow the BACnet Setpoint is a percentage of the MaxCFM 
Setpoint.  When the Damper Mode is set to Position the BACnet 
Setpoint is the percentage the damper is open.  When the Setpoint 
Source is set not set to BACnet this variable has no impact on 
controlling the damper.  

SafetyStatus

BI

1

C

Represents the status of the safety circuit. Inactive = Open/Failure; 
Active  = Closed/OK

MaximumFPM

MV

1

C

Represents the maximum setpoint velocity in fpm.  The value this 
variable is set to corresponds to a 10 VDC input to the actuator.  
This value is set at the factory based on maximum velocity that 
was selected at the time the unit was ordered. 1 = 500 fpm; = 1000 
fpm; 3 = 1500 fpm; 4 = 2000 fpm; 5 = 2500 fpm; 6 = 3000 fpm; 7 = 
3500 fpm; 8 = 4000 fpm

DamperMode

MV

2

C

Establishes the mode of operation for the actuator.  When in flow 
control mode the actuator will view the setpoint as a target cfm 
to maintain.  When in position control mode the actuator will view 
the setpoint percentage as a position to drive to (0% fully closed, 
100% fully open).  Whether the actuator is in Flow or Position 
control mode the source of the setpoint will be determined by the 
Setpoint Source variable.  1 = Flow; 2 = Position

SetpointSource

MV

3

C

When set to BACnet the actuator uses the BACnet variable as 
the setpoint.  When set to Local AI it uses the actuator's second 
analog input (S2) as the setpoint.  When set to Zth the actuator 
uses a handheld Zth module to establish the setpoint. 1 = Local AI; 
2 = BACnet; 3 = ZTH

AI - Analog Input

AO - Analog Output

AV - Analog Value

BI - Binary Input

BO - Binary Output

BV - Binary Value

MI - Multi-State Input

MO - Multi-State Output

MV - Multi-State Value

R - ReadOnly

W - Writable

C -  Commandable (Contains 

Priority Array)

BACNet Data Point List

AMD-xx-TD Series

7

Содержание AMD TD Series













Отзывы: