background image

DESULFATION

The  operator  can  every  time  interrupt  the  standard  charging  and  enable  with  a  easy procedure a special desulfation 

cycle. During the charging the operator can press Enter few seconds and the display shows a desulfation menu, in this menu 

the operator can select the time  during of  desulfation  and  the  type  of  restart of  desulfation, in fact sometimes  it is 

strategic important to complete a standard charging after a completed desulfation cycle.

REFRESH-MAINTENANCE

This function is useful to keep the battery in perfect condition when it’s not used for an long period (weeks, months, ...).

It is sufficient to leave the battery connected to the charger. After a normal termination of the charge and the equalize cycle, 

the control board  will activate the charger automatically for 15 minutes of refresh charge every day.

While the charger waits before to activate a Refresh cycle, the display shows the messages:

•   Battery Voltage 

[Volt]

•   Nr of Refresh cycles already given to the battery

•   Total Time of Charge 

[hours.minutes]

•   Total Capacity Returned 

[Ah]

During cycle Refresh, the display shows the same set of information that are visualized during the normal charge cycle.

DISCONNECTION OF THE BATTERY DURING THE CHARGE

The charger will suspend the charge and the display will show the message:

At this time it’s possible to disconnect the battery.
Eventually, the charge can be restarted, by pressing the button UP for 5 seconds.

GECI

 BLACK DIAMOND CHARGER

PROGRAMMING BATTERY ID MODULE 

When a battery ID module is installed on a battery for the first time, it must be initialized and programmed, by following 

this procedure. Connect the battery to a AR-TOP charger (the Battery Recognition mode 

must be set to BATTERY ID MODULE or OPTIONAL). The AR-TOP charger will establish 

a communication with the New Battery ID module, and it will show the message:

At this point, using the UP/DOWN buttons, it’s possible to edit the battery ID information:

•   ID Number  (8 alphanumeric digits, to be confirmed individually by pressing ENTER for 3 seconds)

•   Nominal Voltage

•   Capacity

•   Type

Once all the parameters are set correctly, push the buttons 

UP+DOWN Simultaneously 

in order to save the data to the ID module. The programming sequence may take up to 

3 minutes, while the charger display will show the message:

>>>WARNING !<<<

DON’T DISCONNECT THE BATTERY DURING THE CHARGE. RISK OF EXPLOSION!!!
If it’s necessary to disconnect the battery while it’s being charged, press the button UP for five seconds, in 

order to stop the charger manually.

[V.140 – January 2011]

 

IBCI BLACK DIAMOND

 

User's Manual

 

Page 20/28 

 

 

 

REFRESH-MAINTENANCE  

 

 

This function is useful to keep the battery in perfect condition when it's not used for an long 

period (weeks, months, ...). 

 

It is sufficient to leave the battery connected to the charger. After a normal termination of the 

charge and the equalize cycle, the control board   will activate the charger automatically for 

15 minutes of refresh charge every day. 

 

While the charger waits before to activate a Refresh cycle, the display shows the messages: 

 

 

 

xx.x V 

R.END NR

 

xxx Ah 

x.x t

 

 

 

 

•  

Battery Voltage 

[Volt] 

•  

Nr of Refresh cycles already given to the battery 

•  

Total Time of Charge 

[hours.minutes] 

•  

Total Capacity Returned 

[Ah] 

 

During cycle Refresh, the display shows the same set of information that are visualized 

during the normal charge cycle. 

 

 

DISCONNECTION OF THE BATTERY DURING THE CHARGE  

 

 

 

WARNING !

 

DON'T DISCONNET THE BATTERY DURING THE CHARGE.

 

RISK OF EXPLOSION!!!

 

 

 

 

If it's necessary to disconnect the battery while it's being charged, press the 

button UP for five seconds, in order to stop the charger manually.

 

 

The charger will suspend the charge and the display will show the message: 

 

 

 

MANUAL 

STOP

 

 

 

 

At this time it's possible to disconnect the battery. 

 

Eventually, the charge can be restarted, by pressing the button UP for 5 seconds. 

[V.140 – January 2011]

 

IBCI BLACK DIAMOND

 

User's Manual

 

Page 21/28 

 

 

 

 

 

5. PROGRAMMING BATTERY ID MODULE  

 

 

 

 

 

When a battery ID module is installed on a battery for the first time, it must be initialized and programmed, by 

following this procedure. 

 

Connect  the  battery  to  a  AR-TOP  charger  (the  Battery  Recognition  mode  must  be  set  to  BATTERY  ID 

MODULE or OPTIONAL). 

 

The AR-TOP charger will establish a communication with the New Battery ID module, and it will show the 

message: 

 

 

BATT ID MODULE 

CONNECTED

 

 

 

 

At this point, using the UP/DOWN buttons, it's possible to edit the battery ID information: 

 

•  

ID Number 

(8 alphanumeric digits, to be confirmed 

individually by pressing ENTER for 3 seconds) 

•  

Nominal Voltage 

•  

Capacity 

•  

Type 

 

Once all the parameters are set correctly, push the buttons 

UP+DOWN Simultaneously 

in order to save the 

data to the ID module. 

The programming sequence may take up to 3 minutes, while the charger display will show the message: 

 

 

 

BATT ID MODULE 

PROGRAMMING...

 

 

 

 

When the programming sequence is completed, the display will show the message: 

 

 

 

BATT ID MODULE 

SET = OK!

 

 

 

At this point, it's possible to disconnect the battery from the charger. 

If the battery is left connected, a charge cycle will be initiated. 

The Battery ID Module will keep the information in memory for an unlimited time. 

[V.140 – January 2011]

 

IBCI BLACK DIAMOND

 

User's Manual

 

Page 21/28 

 

 

 

 

 

5. PROGRAMMING BATTERY ID MODULE  

 

 

 

 

 

When a battery ID module is installed on a battery for the first time, it must be initialized and programmed, by 

following this procedure. 

 

Connect  the  battery  to  a  AR-TOP  charger  (the  Battery  Recognition  mode  must  be  set  to  BATTERY  ID 

MODULE or OPTIONAL). 

 

The AR-TOP charger will establish a communication with the New Battery ID module, and it will show the 

message: 

 

 

BATT ID MODULE 

CONNECTED

 

 

 

 

At this point, using the UP/DOWN buttons, it's possible to edit the battery ID information: 

 

•  

ID Number 

(8 alphanumeric digits, to be confirmed 

individually by pressing ENTER for 3 seconds) 

•  

Nominal Voltage 

•  

Capacity 

•  

Type 

 

Once all the parameters are set correctly, push the buttons 

UP+DOWN Simultaneously 

in order to save the 

data to the ID module. 

The programming sequence may take up to 3 minutes, while the charger display will show the message: 

 

 

 

BATT ID MODULE 

PROGRAMMING...

 

 

 

 

When the programming sequence is completed, the display will show the message: 

 

 

 

BATT ID MODULE 

SET = OK!

 

 

 

At this point, it's possible to disconnect the battery from the charger. 

If the battery is left connected, a charge cycle will be initiated. 

The Battery ID Module will keep the information in memory for an unlimited time. 

[V.140 – January 2011]

 

IBCI BLACK DIAMOND

 

User's Manual

 

Page 20/28 

 

 

 

REFRESH-MAINTENANCE  

 

 

This function is useful to keep the battery in perfect condition when it's not used for an long 

period (weeks, months, ...). 

 

It is sufficient to leave the battery connected to the charger. After a normal termination of the 

charge and the equalize cycle, the control board   will activate the charger automatically for 

15 minutes of refresh charge every day. 

 

While the charger waits before to activate a Refresh cycle, the display shows the messages: 

 

 

 

xx.x V 

R.END NR

 

xxx Ah 

x.x t

 

 

 

 

•  

Battery Voltage 

[Volt] 

•  

Nr of Refresh cycles already given to the battery 

•  

Total Time of Charge 

[hours.minutes] 

•  

Total Capacity Returned 

[Ah] 

 

During cycle Refresh, the display shows the same set of information that are visualized 

during the normal charge cycle. 

 

 

DISCONNECTION OF THE BATTERY DURING THE CHARGE  

 

 

 

WARNING !

 

DON'T DISCONNET THE BATTERY DURING THE CHARGE.

 

RISK OF EXPLOSION!!!

 

 

 

 

If it's necessary to disconnect the battery while it's being charged, press the 

button UP for five seconds, in order to stop the charger manually.

 

 

The charger will suspend the charge and the display will show the message: 

 

 

 

MANUAL 

STOP

 

 

 

 

At this time it's possible to disconnect the battery. 

 

Eventually, the charge can be restarted, by pressing the button UP for 5 seconds. 

Содержание GECI
















Отзывы: