Gree GMV-1015WM/H-X Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 77

background image

GMV DC Inverter VRF

67

Phenomenon

Reason

Measure

Abnormal cooling or
heating

Door or windows are opened

Close the door or windows

Direct sunshine

Draw curtain or louver

Too many people in the room

——

Too many heat resources in the room

Reduce heat resources

Filter is blocked for dirt

Clean the filter

NOTE!

If problem cannot be solved after checking the above items, please contact Gree service center

and show phenomena and models.

Following circumstances are not malfunction.

“Malfunction”

Reason

Unit doesn't run

When unit is started immediately after it is just
turned off

Overload protection switch makes it run after
3 minutes delay

When power is turned on

Standby operating for about 1 minute

Mist comes from

the unit

Under cooling

Indoor high humidity air is cooled rapidly

Noise is emitted

Slight cracking sound is heard when just turned
on

It is noise when electronic expansion valve
initialization

There is consecutive sound when cooling

That's sound for gas refrigerant flowing in unit

There is sound when unit starts or stops

That's sound for gas refrigerant stops to flow

There is slight and consecutive sound when unit
is running or after running

That's sound for operation of drainage system

Cracking sound is heard when unit is operating
and after operating

That's sound caused by expansion of panel
and other parts due to temperature change

The unit blows out

duct

When unit runs after no operation for a long
period

Dust in indoor unit is blew out

The unit emits odor Operating

The room odor absorbed by the unit is blew
out again

Indoor unit still runs

after switch off

After every indoor unit receive "stop" signal, fan
will keep running

Indoor fan motor will keep running 20-70s so
as to take good use of excess cooling and
heating and prepare for next operation

Mode conflict

COOL or HEAT mode can't be operated

When the indoor operating mode conflicts
with that of outdoor unit, indoor fault indicator
will flash and conflict will be shown on the
wired controller after 5 minutes. Indoor unit
stops to run and meanwhile change outdoor
operating mode as the same as that of indoor
unit, then the unit will go back to normal.
COOL mode doesn't conflict with DRY mode.
FAN mode doesn't conflict with any mode.

«
...
69
70
71
72
73
...
»

Содержание GMV-1015WM/H-X














































































Отзывы:

Нет отзывов

Похожие инструкции для GMV-1015WM/H-X

Бренд: ABB Страницы: 78

Бренд: Paradox Страницы: 2

Бренд: Makita Страницы: 20

Бренд: Velleman Страницы: 48

Бренд: N-Tron Страницы: 2

Бренд: Future Illuminations Страницы: 2

Бренд: Perle Страницы: 23

Бренд: SAJ Страницы: 32

Бренд: Gesan Страницы: 80

Бренд: Zamp Solar Страницы: 7

Click Board ADC 3 click

Бренд: Mikroe Страницы: 2

Smart AC Inverter 100 USB

Бренд: Wagan Страницы: 5

Бренд: axing Страницы: 138

Бренд: Pulse-Eight Страницы: 2

HUBNER BERLIN AMG 11 FSL

Бренд: Baumer Страницы: 44

Бренд: Intellinet Страницы: 16

Бренд: Mayty Страницы: 14

Extron Electonics YCV 100

Бренд: CAMBOARD Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды