Gree GMV-1015WM/H-X Скачать руководство пользователя страница 59

Страница: 59 / 77

GMV DC Inverter VRF

(4) Display instruction for each stage progress at the time of debugging:

Instruction for each stage progress at the time of debugging

——

Debugging

code

Progress code

Status code

Meaning

Progress

LED1

LED2

LED3

Code

Display

status

Code

Display

status

Code

Display

status

01_ set up

master unit

Undebugged status.

The system hasn't set master module. It needs
to reset it.

The system has set more than 2 master
modules. It needs to reset it.

Master module setting is succeeded. It will
automatically enter into the next step.

02_

llocate

addresses

Flash

The system is conducting the address
assignment.

Address assignment is succeeded. It will
automatically enter into the next step.

03_module

qunaity

confirmation

01~04

Flash

LED3 displays the module quantity. It needs to
manually confirm the module quantity.

Once the system module quantity is confirmed,
it will automatically enter into the next step for
judgment.

04_indoor

unit's quantity

confirmation

××/ The

quantity

of online

indoor

units

Flash

LED3 displays the quantity of online indoor
units.

Indoor unit's quantity inspection is finished.
Enter into the next step automatically.

05_ detect

internal

communicatio

The system has detected “communication
malfunction between main control and inverter
compressor driver”.

The system has detected “communication
malfunction between main control and inverter
fan driver”.

Indoor/outdoor unit's “rated capacity ratio is too
high”.

Indoor/outdoor unit's “rated capacity ratio is too
low”.

System inspection is finished. Enter into the
next step automatically.

06_ outdoor

unit's internal

components
confirmation

correspod

ing error

code

The system has detected the fault of outdoor
unit's components.

The system detected that there's no outdoor
unit fault. Enter into the next step
automatically.

Содержание GMV-1015WM/H-X














































































Результаты поиска

Содержание GMV-1015WM/H-X

Отзывы:

Похожие инструкции для GMV-1015WM/H-X

Бренды по названию

Популярные бренды

Gree GMV-1015WM/H-X, Руководство пользователя

Результаты поиска

Содержание GMV-1015WM/H-X

Отзывы:

Похожие инструкции для GMV-1015WM/H-X

Бренды по названию

Популярные бренды