Gree GMV-1015WM/H-X Скачать руководство пользователя страница 39

Страница: 39 / 77

GMV DC Inverter VRF

Step

Photo

Operation instruction

Note

Step 5

①

Pull the canvas casing

upside down and press
it on the butt flange of
the steel pipe
ventilation pipe with
steel bars;

②

Drill holes with the

manual drill and fix
them with
self-tapping screws;

③

Seal the two butt joints

with tinfoil panel and
check the reliability of
the connection.

___

3.6 Vacuum and Drying of Refrigeration System

3.6.1 Air Tightness Test

(1)

Notices

1) The range of test pressure gauge for R410A system should be above 4.5MPa.

2) Record the pressure gauge readings, ambient temperature and test time.

3) Pressure correction: The temperature changes by 1

℃

, and the pressure changes by

0.01MPa.

4) The pressure should remain unchanged to be qualified.

5) If it is necessary to maintain pressure for a long time, the pressure should be reduced to

0.5MPa or less. Long periods of high pressure can cause leakage at the weld site and

there is safety hazard.

6) Before the air tightness test for the refrigerant pipe is completed, it is not allowed to

conduct the insulation and wrapping work for any joints between the welding point and

the bell mouth of indoor unit. Please increase pressure from the outdoor side pipes at

the same time. It is forbidden to increase pressure from one side pipe:

Содержание GMV-1015WM/H-X














































































Результаты поиска

Содержание GMV-1015WM/H-X

Отзывы:

Похожие инструкции для GMV-1015WM/H-X

Бренды по названию

Популярные бренды

Gree GMV-1015WM/H-X, Руководство пользователя

Результаты поиска

Содержание GMV-1015WM/H-X

Отзывы:

Похожие инструкции для GMV-1015WM/H-X

Бренды по названию

Популярные бренды