background image

Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller 
is locked, the icon
flicker for three times. If the keyboard is unlocked, the mark will disappear. 

1. Press swing up and down button continuously more than 2s,the main unit will swing back 

and forth from up to down, and then loosen the button, the unit will stop swinging and present 
position of guide louver will be kept immediately.

2. Under swing up and down mode, when the status is switched from off to     , if press this

button again 2s later,     status will switch to off status directly; if press this button again 
within 2s,the change of swing status will also depend on the circulation sequence stated above. 

About switch between Fahrenheit and Centigrade

Under status of unit off, press MODE and - buttons simultaneously to switch

℃ 

and

 

About swing up and down

About lock

        will be displayed on it, in which case, press any button, the mark will

Operation of wireless remote control

1.

Changing batteries and notices

10

.

.

3.


Slightly to press the place with      , along the arrowhead direction to push the back cover of wireless 

 remote  control. (As show in figure)

Take out the old batteries. (As show in figure)
 Insert two new AAA1.5V dry batteries, and pay attention to the polarity. 

 (As show in figure)
 Attach the back cover of wireless remote control. (As show in figure)

When changing the batteries, do not use the old or different batteries,  

If the wireless remote control will not be used for a long time, please 

otherwise, it can cause the malfunction of the wireless remote control.

take them out, and don't let the leakage liquid damage the wireless 

remote control.

The operation should be in its receiving range.
It should be placed at where is 1m away from the TV set or stereo sound sets.
If the wireless remote control can not operate normally, please take them out, 

 after 30s later and reinsert, if they cannot normally run, please change them.

Sketch map for 

changing batteries

NOTE:

Содержание GIS409AC





























Отзывы: