background image

6

Press this button to set up &down swing angle, which circularly changes as below:

OFF

This remote controller is universal. If any command        ,           or          is sent out,

the unit will carry out the command as

8

P

ress this button to achieve the on and off of healthy and scavenging functions in

operation status. Press this button for the first time to start scavenging function;

LCD displays“     ”. Press the button for the second time to start healthy and scavenging

functions simultaneously; LCD displays“     ” and “     ” . Press this button for the third

time to quit healthy and scavenging functions simultaneously.Press the button for the

fourth time to start healthy function; LCD display “      ”. Press this button again to repeat

the operation above. (Not available on all models              

)

/

8

Press this button to turn on I FEEL function. The unit automatically adjust temperature

according to the sensed temperature. Press this button again to cancel I FEEL function. 

I FEEL:

SWING:

7

Remote Controller Description

ON/OFF:

MODE :

+

:

This button is used for setting Fan Speed in the sequence that goes from AUTO,

to

then back to Auto.

,

,

,

FAN :

1

4

3

2

5

Operation of Remote Controller

Press this button to turn on the unit . Press this button again to turn off the unit.

Press this button to decrease set temperature. Holding it down above 2 seconds rapidly
decreases set temperature. In AUTO mode, set temperature is not adjustable. 

Press this button to increase set temperature. Holding it down above 2 seconds rapidly

increases set temperature. In AUTO mode, set temperature is not adjustable. 

Auto

Low speed

Medium speed

High speed

Each time you press this button, a mode is selected in a sequence that goes from AUTO,

COOL, DRY, FAN, and HEAT

*

, as the following:

AUTO

COOL

DRY

FAN

HEAT

*

*Note:Only for models with heating function.

After energization, AUTO mode is defaulted. In AUTO mode, the set temperature will not

be displayed on the LCD, and the unit will  automatically select the suitable operation 

mode in accordance with the room temperature to make indoor room comfortable.

(As for cooling only unit, it won’t have any action when it receives the signal of heating 

operation.)

indicates the guide louver swings as:

Содержание Cozy

































Отзывы: