background image

2

1.Safety Precaution

Important!

This air conditioning system meets strict safety and

operating standards. As the installer or service person,

it is an important part of your job to install or service the

system so it operates safely and efficiently.

Follow each installation or repair step exactly as shown.

Observe all local, state, and national electrical codes.

Pay close attention to all warning and caution notices

given in this manual.

To prevent injury to the user or other people and

property damage, the following instructions must

be followed.

About the pict

ures

:

Erroneous handing gives a high possi-

bility to induce serious results such as

death or heavy injury.

Erroneous handing may induce serious

injury depending on the situation.

Do not supply power to the unit until all wiring and tubing

are completed or reconnected and checked.

Highly dangerous electrical voltages are used in this

system. Carefully refer to the wiring diagram and these

instructions when wiring. Improper connections and inad-

equate grounding can cause accidental injury or death.

Ground the unit following local electrical codes.

Connect all wiring tightly. Loose wiring may cause over-

heating at connection points and a possible fire hazard.

All electric work must be performed by licensed technician,

 

ac-

cording to local regulations and the instructions given in this

manual.

There is risk of fire, electric shock, explosion, or injury.

Ask your dealer or specialized subcontractor for installation or

repair work.

Make sure the ceiling/wall is strong enough to hold the

unit’s weight. The outdoor unit shou

l

d be installed in a

location where air and noise emitted by the unit will not

disturb the neighbors.

Properly insulate any tubing run inside a room to prevent

"sweating" that can cause dripping and water damage to

walls and floors.

The outdoor unit must be installed on stable, level surface,

in a place where there is no accumulation of snow, leaves

or rubbish.

The unit should be installed according to the instructions

in order to minimize the risk of damage from earthquakes,

typhoons or strong winds.

When the refrigerant touches the fire e

t

c., it was decomposed

and a poisonous gas is generated.

Use only the specified refrigerant to charge the re

f

rigerant

circuit.

Do not mix it with any other refrigerant and do not allow air to

remain in the circuit.

Air enclosed in the circuit can cause high pressure resulting

in a rupture and other hazards.

After completing installation work, make sure that refriger-

ant gas has not leaked.

The limit density is made not to be exceeded even if the refrig-

erant leaks by any chance.

Turn the power off at the main power box (mains) before open-

ing the unit to check or repair electrical parts and wiring.

Keep your fingers and clothing away from any moving parts.

Clean up the site after you finish, remembering to check that

no metal scraps or bits of wiring have been left inside the unit

being serviced.

The unit must be properly earth connected.

Caution

Warning

Warning

Caution

Never in

s

tall on the place where a combustible gas might

leak.

The gas may ignite or explode when the gas leaks and

collects in surround of the unit.

When the unit is installed at telecommunication centers or

hospitals, take a proper provision against noise.

When installing at a watery place, provide an electric leak

breaker.

Do not wash the unit with water.

Be very careful about unit transportation.

 

The unit shou

l

d not

be carried by only one person if it is more than 20kg. It occasion-

ally causes the damage of th

e

 unit and health to be impaired.

Do not touch the heat exchanger fins w

i

th your hands.

Doing so may cut your hands.

Do not touch the compressor or refrigerant piping without

wearing glove on your hands. 

Touching directly such part can

cause a burn or frostbite as it becomes high or low temperature

according to the refrigerant state.

Do not operate the air conditioner without the air filter set

place. Dust may accumulate, and cause a failure.

At emergency (if you smell something burning), stop opera-

tion and turn the power source switch off.

Safety Precautions

Содержание CE012N03600















































Отзывы: