background image

Robart Super Stand II (ROBP1402)

CG Machine

(GPMR2400)

Precision Magnetic Prop Balancer

(TOPQ5700)

When you see the term 

test fit in the instructions, it

means that you should first position the part on the
assembly without using any glue, and then slightly modify
or 

custom fit the part as necessary for the best fit.

This kit contains primarily metric hardware with just a

couple of exceptions.

Photos and sketches are placed before the step they

refer to. Frequently you can study photos in following steps
to get another view of the same parts.

The stabilizer and wing incidences and motor thrust

angles have been factory-built into this model. However,
some technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at www.greatplanes.com and click on “Technical Data.”
Due to manufacturing tolerances which will have little or no
effect on the way your model will fly, please expect slight
deviations between your model and the published values.

Fuse = Fuselage

Stab = Horizontal Stabilizer

Fin = Vertical Fin

LE = Leading Edge

TE = Trailing Edge

LG = Landing Gear

Ply = Plywood

" = Inches

mm = Millimeters

ESC = Electronic Speed Control

Replacement parts for the Great Planes Fokker D.VII EP ARF
are available using the order numbers in the Replacement
Parts List 
that follows.The fastest, most economical service can
be provided by your hobby dealer or mail-order company.

To locate a hobby dealer, visit the Hobbico

®

web site at

www.hobbico.com. Choose “Where to Buy” at the bottom
of the menu on the left side of the page. Follow the
instructions provided on the page to locate a U.S., Canadian
or International dealer.

Parts may also be ordered directly from Hobby Services by
calling (217) 398-0007, or via facsimile at (217) 398-7721, but
full retail prices and shipping and handling charges will apply.
Illinois and Nevada residents will also be charged sales tax. If
ordering via fax, include a Visa

®

or MasterCard

®

number and

expiration date for payment.

Mail parts orders and payments by personal check to:

Hobby Services

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822

Be certain to specify the order number exactly as listed in the
Replacement Parts List. Payment by credit card or personal
check only; no C.O.D.

If additional assistance is required for any reason contact Product
Support by e-mail at [email protected],
or by telephone at (217) 398-8970.

Replacement Parts List 

GPMA3015 ..............Top Wing Set
GPMA3016 ..............Bottom Wing Set
GPMA3017 ..............Fuse Set
GPMA3018 ..............Tail Surface Set
GPMA3019 ..............Cowl/Cheek Vent Set
GPMA3020 ..............Cabanes Set
GPMA3021 ..............N Strut Set
GPMA3022 ..............Machine Gun Set
GPMA3023 ..............Landing Gear
GPMA3010 ..............Wheels (2)
GPMA3011 ..............Pilot

ORDERING REPLACEMENT PARTS

COMMON ABBREVIATIONS

IMPORTANT BUILDING NOTES

4

To convert inches to millimeters, multiply inches by 25.4

Содержание Fokker D.VII ARF ElectriFly





















Отзывы: