background image

27

ElectriFly Reactor 3D EP ARF by Great Planes
With its generous wingspan, the Reactor 3D electric ARF is 
easy to handle and track indoors or out. The wing’s ultra-thin 
airfoil allows radical attitude changes and gentle handling 
on approach. Oversized ailerons, adjustable pushrods and 
short, direct linkages combine for crisp, powerful response. 
The structure is factory-built from interlocking, laser-cut 
balsa parts, with covering already applied, and the fiberglass 
cowl and plastic wheel pants are painted to match. Magnetic 
“latches” on the cowl and battery hatch eliminate the need 
for screw fasteners and offer clean looks and improved 
aerodynamics. Unlike most electrics, the Reactor 3D ARF 
was designed for in-runner or out-runner motors and includes 
mounts for both. GPMA1540

Futaba

®

 S3114 High Torque Micro Servo

Ideal for electric planes and small electric helis, the affordable, 
analog S3114 delivers plenty of power and performance in a 
compact package. FUTM0414

Great Planes ElectriFly RimFire

 35-30-1250kV

Out-Runner Brushless Motor
For explosive acceleration and maximum torque, nothing 
is hotter than a RimFire! A lightened aluminum can houses 
high-torque, “rare-earth” Neodymium magnets, and RimFire 
motors feature better cooling – which means 50% more 

power than similar-sized out-runners. Bearings are double-
shielded, and because they are no comms or brushes to worry 
about, RimFire motors are super-dependable and virtually 
maintenance-free! Motor comes with prop adapter, mount, 
hardware and preinstalled, gold-plated bullet connectors 
compatible with all ElectriFly ESCs. GPMG4595

Great Planes ElectriFly Ammo

 24-45-3790kV

In-Runner Brushless Motor
Powered by “rare-earth” Neodymium magnets, Ammo 
motors boast exceptionally high torque and unmatched heat 
resistance. Up to 89% effi cient and virtually maintenance-
free, they feature double-shielded bearings, with no brushes 
to wear out. Gold-plated connectors are preinstalled for 
simple plug-and-play operation; in fact, not even soldering is 
required when used with compatible ElectriFly Silver Series 
brushless ESCs. GPMG5185

Great Planes ElectriFly BP 11.1V 2100mAh 15C Balanced 
LiPo Battery
Enjoy exceptional performance for less money with this 
balanced LiPo pack! Quality Deans

®

 Ultra

 connectors 

make this a real value for Sunday fl iers. Plus, you get all the 
benefi ts of balancing, such as knowing that all cells are fully 
charged for maximum power, they’re conditioned better to 
last longer, and they’re safe to handle*. GPMP0721

*Packs must be balanced using a dedicated cell balancer such as the ElectriFly Equinox

™ 

(GPMM3160) or a properly equipped charger.

Содержание Extra 330S ARF





























Отзывы: