manualshive.com logo in svg

GREAT PLANES Cherokee .40 ARF, Инструкция по эксплуатации, Страница: 22 / 28

Поделиться
Скачать
GREAT PLANES Cherokee .40 ARF Скачать руководство пользователя страница 22

22

Install the Wing & Canopy Hatch

❏ 

1. Fit the two wing panels onto the aluminum wing joiner 

tube. Slide the root ribs of the panels together so that the 
anti-rotation pin preinstalled in one panel fi ts into the 
mating hole of the other panel. Slide the wing dowels that are 
preinstalled in the LE of the wing panels into the receiving 
holes in the fuselage at the front of the wing saddle. Use 
two 1/4-20 nylon wing bolts to secure the wing in place.

❏ 

2. We suggest gluing a #4 washer to each of the two 

4-40 x 5/8" [16mm] canopy hatch screws. Take care not to 
get glue onto the threads of the screws. This will make the 
screws easier to work with at the fl ying fi eld.

❏ 

3. Fit the canopy hatch in place by inserting the two 

dowel pins into the receiving holes at the front of the hatch 
opening. Use the two 4-40 x 5/8" [16mm] machine screws to 
secure the hatch in place.

❏ 

4. This completes the assembly of the Cherokee .40 ARF!

Apply the Decals

1. Use scissors or a sharp hobby knife to cut the decals from 
the sheet. 

2. Be certain the model is clean and free from oily fi ngerprints 
and dust. Prepare a dishpan or small bucket with a mixture 
of liquid dish soap and warm water–about one teaspoon of 
soap per gallon of water. Submerse the decal in the soap and 
water and peel off the paper backing. Note: Even though the 
decals have a “sticky-back” and are not the water transfer 
type, submersing them in soap & water allows accurate 
positioning and reduces air bubbles underneath. 

3. Position the decal on the model where desired. Holding the 
decal down, use a paper towel to wipe most of the water away.

4. Use a piece of soft balsa or something similar to squeegee 
remaining water from under the decal. Apply the rest of the 
decals the same way. 

GET THE MODEL READY TO FLY

Install & Operate the Motor Battery 

(Brushless Only)

IMPORTANT: If using multiple battery packs that are connected 
with an adapter, never charge the batteries together through 
the adapter. Always charge each battery pack separately. 
Charge the batteries, then read the following precautions on 
how to connect multiple packs for fl ying the model.

Содержание Cherokee .40 ARF





























Отзывы:

Нет отзывов