manualshive.com logo in svg

GREAT PLANES Cherokee .40 ARF, Инструкция по эксплуатации, Страница: 19 / 28

Поделиться
Скачать
GREAT PLANES Cherokee .40 ARF Скачать руководство пользователя страница 19

19

❏ 

6. Fit a 5/32" [4mm] wheel collar into the nylon steering 

arm, aligning the threaded hole in the collar with the hole 
in the arm. Loosely thread a 6-32 x 1/4" [6mm] SHCS (with 
threadlocking compound) through the hole in the arm and 
into the collar. Install a brass screw-lock pushrod connector 
using a nylon retainer into the outer hole on the steering arm. 
Loosely thread a 4-40 x 1/8" [3mm] SHCS into the screw-
lock pushrod connector.

❏ 

7. Fit the steering arm between the nylon steering block 

halves. Insert the nose gear wire up through the steering 
block and through the steering arm as shown. Tighten the 
SHCS against the fl at spot in the nose gear wire.

❏ 

8. Align the bottom edge of the steering block with the 

bottom edge of the hardwood mounting plate on the fi rewall. 
Mark the locations of the four steering block mounting holes 
onto the hardwood plate. Drill 3/32" [2.4mm] holes at the 
marks you made. Mount the steering block onto the hardwood 
plate using four #4 x 5/8" [16mm] self-tapping screws, being 
sure to harden the holes with thin CA.

❏ 

9. Cut off the threads from the remaining 12" [305mm] 

pushrod, leaving all of the unthreaded portion of the 
pushrod intact. Make a mark 3/16" [4.8mm] from one end 
of the pushrod and make a 90° bend at the mark. Fit the 
unbent end through the steering pushrod hole in the second 
fuselage former and out the hole in the fi rewall. Fit the forward 
pushrod end into the brass screw-lock pushrod connector on 
the nylon steering arm. Insert the bent end of the pushrod 
into the second inner hole in the unused side of the rudder 
servo arm. Secure the pushrod onto the servo arm using a 
nylon FasLink. With the rudder servo arm perpendicular to 
the servo case, rotate the nose gear wire so that the nose 
wheel is pointing straight. Tighten the SHCS in the brass 
screw-lock pushrod connector against the pushrod.

Содержание Cherokee .40 ARF





























Отзывы:

Нет отзывов