GREAT PLAINS YP2425 Скачать руководство пользователя страница 149

Страница: 149 / 166

YP2425 and YP2425F

Table of Contents

Index

Appendix C - Option Installation

145

2016-11-16

Table of Contents

Index

401-406M

Weight Transfer System

This option provides two cylinders and a control valve
that transfer up to 1000 pounds (450 kg) of mainframe
weight to each wing.

This option is factory-installed if ordered with the planter
(feature code 70). See page 43 for operation.

402-520A Low Speed Kit Installation

See “

Low Speed Kit

” on page 113 for the purpose of this

installation.

Shut off any hydraulic source that powers the
hydraulic seed meter drives (dedicated remotes or
PTO).

Refer to Figure 145

At the hydraulic drive motor, loosen the idler nut

Slide the idler out of engagement with the existing
chain

. Remove and save the existing chain:

136

247D CHAIN RL #60 41 PITCHES

Loosen the set screws securing the existing 16T
sprocket

. Remove and save the sprocket:

808

388C SPKT 60B16 X 1 BORE W/KWAY, SS

Leave the woodruff key

in place.

Select one new 10T sprocket:

808

479C SPKT 60B10 X 1 BORE W/KWAY 2SS

Install it on the motor shaft. Secure it with the
woodruff key and two set screws provided.

Select one new:

136

285D CHAIN RL #60 38 PITCHES

Consult page 99 and the directional arrows
shown on the page for proper chain clip orientation.
Install the new chain on the new sprocket and
existing driven sprocket.

Engage the idler for

inch (2.1 cm/m) slack.

Secure the idler nut

Option Package

Part Number

YP24 WEIGHT TRANSFER

411-174A

Field Results Risk:
Do not change the sprocket ratios in the DICKEY-john

IntelliAg

hydraulic drive setup.

Figure 145

Low Speed Kit Sprocket

36355

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды