GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 53

Страница: 53 / 190

YP4025A-48TR20

Table of Contents

Index

Operating Instructions

2019-03-19

Table of Contents

Index

411-198M

Weight Transfer Operation (Option)

This option provides a control valve

, plumbed into the

hydraulic drive circuit, and a cylinder for each wing.

Up to 1000 pounds (450 kg) of mainframe weight may be

transferred to each wing when oil is being supplied to the

hydraulic drive circuit.
Once set, the circuit usually requires little adjustment in

normal field operations. To set the circuit:
1. Unfold and lower the implement name in field

conditions.

2. Supply oil to the hydraulic drive circuit (or operate

the PTO at field rpm if using a PTO pump that

supplies the hydraulic drive). The hydraulic drive

motor itself does not need to be operated.

3. Loosen the lock disc at the valve block. Adjust the

knob until the gauge

reads approximately

1000 psi. Tighten the lock disc.

4. Lower the implement name. Engage the hydraulic

drive (with seeding disabled) Pull forward at normal

field speed for a short distance. Stop.

5. Check that the wings are level.

See page 17 and page 166 for important information

about movements without a suitable tractor. See

page 136 for ordering information.

Monitor Operation

Monitor operation is described in a separate manual

supplied with your implement name.
Operations covered in that manual (and therefore not in

this manual) include:

•

hydraulic drive control

•

seed rate calibration

•

planting rate

•

fertilizer rate

•

setting rate limits and detecting out-of-limits

•

GPS integration

•

fan rpm

•

If the wings ends are lower than the center,
decrease the pressure at the valve .

•

If the wing ends are higher than the center,
increase the pressure.



A relief valve in the valve block prevents any

damage from over-pressure.

Figure 48

Weight Transfer Valve and Cylinder

36421

Figure 49

Seed Monitor Console

29801

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды