GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 170

Страница: 170 / 190

2019-03-19

Table of Contents

Index

411-198M

YP4025A-48TR20

Table of Contents

Index

Appendix B - Initial Setup

166

Initial Setup

These items may not be dealer-installed or dealer

pre-set unless prior arrangements have been made.

Seed Monitor Console Installation

The product’s standard seed monitor system includes a

virtual terminal and switch panel that must be mounted in
the tractor cab. As supplied by DICKEY-john

, the kit

includes a flat bracket for the modules, and a ball swivel

for mounting the bracket in the tractor.

Transport and Field Safety Risk:

Mount the modules so that they are easy to monitor during
planting, but do not interfere with safe operation of the tractor

in the field or on public roads.

The ball swivel includes four 10-32 screws. You or your

dealer must provide the mounting holes for the screws.

Your dealer may have alternate suction cup or clamping

brackets available if you prefer to avoid drilling holes.

Refer to the included DICKEY-john

manual for harness

connections.

Weight Transfer Shipping Links

If optional weight transfer is not installed, continue at

“

Dual Marker Speed Adjustment

” on page 167.

When a implement name is on customer premises, and

further movements will only be done with a tractor or

towing vehicle having hydraulic motor return and case

drain remote ports, remove the weight transfer shipping

links.
1. Use a hoist or a second worker to support the weight

of the outboard end of a weight transfer cylinder .

2. Remove both cotter pins and clevis pins:

805-058C PIN COTTER 3/16 X 2

805-396C PIN CLVS 1.0X3.13 USBL

from each end of a shipping link:

411-175H WT SHIP LINK

Remove the link.

3. Swing the cylinder down. Align the clevis with the

wing lug . Secure with one of the clevis pins and

cotters.

4. Store the other clevis pin and cotter in the clevis end

of the link. Store the link for future use.

5. Repeat step 1 through step 4 for the other wing.
To install a link, complete step 4 through step 1 in

reverse order.
See page 49 for initial weight transfer setup.

Figure 148

Terminal and Switch Panel

26303

Figure 149

Weight Transfer Shipping Link

36422

858-295C

DO NOT MOVE PLANTER FOLDED
OR UNFOLDED WITHOUT CONNECTING
FAN CASE DRAIN AND LOW PRESSURE
RETURN TO THE TRACTOR OR
INSTALLING WEIGHT TRANSFER
SHIPPING LINKS. FAILURE TO DO
SO CAN RESULT IN DAMAGE TO
WEIGHT TRANSFER CIRCUIT.

NOTICE

39
40

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды