GREAT PLAINS Terra Max HT1110-6.0M Скачать руководство пользователя страница 14

Страница: 14 / 42

Great Plains

| 588-206M | 3/21/22

Table of Contents

HT1110-6.0M & 7.5M

Table of Contents

Adjustments and Installation

This section helps you prepare your tractor and Terra Max for use, and covers tasks that need to be done for new

machines, seasonally, or when the tractor/Terra Max configuration changes.
Before using the Terra Max in the field, you must hitch it to a suitable tractor, inspect systems and level the Terra Max.

Before using the Terra Max for the first time, and periodically thereafter, certain adjustments and calibrations are

required.

Pre-Operation Checklist

Complete this checklist before routine setup:



Read and understand “

Safety Information

” on page 2.



Check that all working parts are moving freely, bolts are tight, and cotter pins are spread.



Make sure your tractor horsepower matches the implement you are pulling. This is important so the implement can do the

best possible job.



Clean all hydraulic couplings and connect to tractor, see “

Hydraulic Hose Hookup

” on page 13.



If machine is folded, unlock wings and open wing lock valve then slowly unfold the unit. Make sure no one is under the wings

during the unfolding process.



Check again for hydraulic leaks and watch that hoses do not get pinched in hinges, wing stops, etc.



After the machine is completely unfolded, raise and lower the Terra Max several times to purge air from the hydraulic system.

Again check for hydraulic leaks and tighten or replace if necessary.



Check safety chain hookup. Make sure all warning lights are hooked up and functioning correctly.



Check that all safety decals and reflectors are correctly located and legible. Replace if damaged. See “

Safety Decals

” on

page 6.



Inflate tires to pressure recommended and tighten wheel bolts as specified. See “

Tire Inflation Chart

” on page 30.



Refold the machine slowly, then lock wings and close wing lock valve. Always place wing locks in locked position when

moving from field to field. Put transport locks into place. You are now ready to go to the field.

Содержание Terra Max HT1110-6.0M











































Результаты поиска

Содержание Terra Max HT1110-6.0M

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Terra Max HT1110-6.0M, Руководство оператора

Результаты поиска

Содержание Terra Max HT1110-6.0M

Отзывы:

Бренды по названию

Популярные бренды