GREAT PLAINS Terra Max HT1110-6.0M Скачать руководство пользователя страница 34

Страница: 34 / 42

Great Plains

| 588-206M | 3/21/22

Table of Contents

HT1110-6.0M & 7.5M

Table of Contents

Maintenance and Lubrication

Maintenance

1. Always use the transport lock when working on or doing

maintenance to the Terra Max. If folded, ensure you have

secured wing locks and closed the wing fold valve. Read

and understand all safety decals on your equipment.

2. During the first season of operation, and periodically after

that, check your bolts for tightness.

3. Replace or rotate worn parts as needed -- hinge bolts,

clevis pins, bearings, coulters, etc.

4. Check and tighten or replace any hydraulic leaks. Check

hoses for any leaks. It is important that there are no leaks

on the equipment.

5. Grease wheel bearings sparingly. Over greasing may

cause damage to seals and reduce the life of the bearing.

Coulter, Finishing Reel and Heavy Reel bearings are all

maintenance free and do not require greasing.

6. Check drag bolts for looseness or excessive wear. Your

drag is an important part of the tillage operation.

Tire Inflation Chart

Tire Inflation Chart

Tire Warranty Information

Wheel

Tire Size

Inflation

All tires are warranted by the original manufacturer of the tire. Tire warranty

information is found in the brochures included with your Operator’s and

Parts Manuals or online at the manufacturer’s web sites listed below. For

assistance or information, contact your nearest Authorized Farm Tire

Retailer.

ManufacturerWeb site

Firestonewww.firestoneag.com

Gleasonwww.gleasonwheel.com

Titanwww.titan-intl.com

Galaxywww.atgtire.com

BKTwww.bkt-tire.com

Center

Transport

550/45 - 22.5 22 PR.

80 psi

(551 kPa)

(5.5 bar)

Transport/

Wings

15.0/55 - 17 EURO

54 psi

(372 kPa)

(3.72bar)

Gauge

Wheel

10.0/75 - 15 18Ply

105 psi

(723 kPa)

(7.1 bar)

Содержание Terra Max HT1110-6.0M











































Результаты поиска

Содержание Terra Max HT1110-6.0M

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Terra Max HT1110-6.0M, Руководство оператора

Результаты поиска

Содержание Terra Max HT1110-6.0M

Отзывы:

Бренды по названию

Популярные бренды