Gravely CONVERTIBLE 10 Скачать руководство пользователя страница 42

Страница: 42 / 54

After installing magneto components, run all leads out through hole provided (in 11 o'clock position)

on bearing plate.

Figure 46 - Typical Crankcase Breather

Figure 47 Installing Flywheel

18.

Governor Arm and Linkage

Insert carburetor linkage in throttle arm.

Connect governor arm to carburetor linkage and slide governor arm onto governor shaft.

Before tightening clamp bolt, turn shaft counterclockwise as far as possible with a pair of pliers, pull
arm as far as possible to left (away from carburetor), tighten nut and check for freedom of movement.

15.

Flywheel

Place wave washer on crankshaft and place

flywheel in position. The square key holds

flywheel on shaft.

Install starter pulley, lock washer and holding nut.

Insert a bar between flywheel fins and tighten

holding nut to torque value specified in Clearance

Section.

The rotating screen is fastened to starter pulley

with screws and spacers.

16.

Breaker Points

Install push rod.

Fasten breaker in place with two screws.

Place cover gasket in position and attach magneto

lead.

Set breaker gap at .020 full open. For ignitior

setting, refer to Ignition System Service.

Make preliminary adjustments before installing

breaker point cover. Be sure breaker lead grommet

is in place.

17.

Carburetor

Insert a new gasket and assemble carburetor to

intake port with two screws.

Refer to Service Section on carburetor adjustment

procedure.

Содержание CONVERTIBLE 10























































Результаты поиска

Содержание CONVERTIBLE 10

Отзывы:

Бренды по названию

Популярные бренды

Gravely CONVERTIBLE 10, Руководство по ремонту

Результаты поиска

Содержание CONVERTIBLE 10

Отзывы:

Бренды по названию

Популярные бренды