manualshive.com logo in svg

Gravely CONVERTIBLE 10, Руководство по ремонту

Поделиться
Скачать
Gravely CONVERTIBLE 10 Скачать руководство пользователя страница 38

 

 38

Figure 34 Governor Gear Assembly In Crankcase 

d.

 

Tighten holding screw from outside of cylinder block. Screw prevents governor gear from sliding 

off stub shaft during assembly. 

e.

 

Rotate governor gear assembly to be sure holding screw does not contact weight section of gear. 

Figure 33  Exploded View, Major Components Of Typical Engine 

4.    

Camshaft Installation 

 

a.

 

Turn cylinder block upside down. 

b.

 

Tappets must be installed before camshaft is placed. Insert tappets in valve guides. Exhaust 

tappets are interchangeable. 

c.

 

Position camshaft inside block. 

d.

 

Lubricate rod then insert into block (bearing plate side). Before pushing rod through camshaft, 

slip one .005" washer (end play) between end of camshaft (opposite gear end) and block. Push 

rod through camshaft and tap lightly until rod just starts into bore at P. T. O. end of block. Check 

end play with feeler gauge -- if within tolerance press rod into final position or remove rod and 

add (or substract) .005 and .010" thick washers as necessary to attain proper end play (See Fits 

and Clearance Section). 

e.

 

While rod is a tight press fit at P. T. O. end of block, a light to loose fit is necessary at the bearing 

plate end. New bearing plate gaskets have notch to allow any oil that may leak past to drain back 

into block. 

Содержание CONVERTIBLE 10























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды