GRAUPNER ULTRAMAT 25, Руководство по эксплуатации

Страница: 14 / 32

27 26
8. Selecting the charge program group
9. Using the charger for the first time.
The charge and setup facilities of the ULTRAMAT 25 are easy to
understand, and are logically divided into four program groups.
These cater for the various battery types: there is a separate pro-
gram group for each of the types
Ni ckel- C a d mium, N ickel- M etal-
H ydride, Li thium- Io n / Li thium- Po lymer and Pb (lead) batteries.
An additional program group contains the charger’s basic setup
facilities.
Switching programs:
z
It is only possible to switch from one charge program group to the
next if
no battery is connected to the charge outputs.
If a battery is connected to the unit, it is not possible to switch to
a different charge program group; you must first disconnect the
battery from the charger’s output sockets.
z
It is only possible to switch from one charge program group to the
next when the charger is in
AUTOMATIC mode. This means that
you must first press the MODE button repeatedly until the top line
of the screen displays the message “ AUTOMATIC ”.
z
Press the ENTER button to switch program groups..
When the ULTRAMAT 25 is initially connected to a 12 V car battery, the unit runs through the informa-
tion routine which provides the user with a brief summary of the essential user settings. The charger’s
screen displays the following information in sequence:
The ULTRAMAT 25 informs you of its designation.
The screen displays the voltage of the car battery at which the
charger breaks off the charge / discharge process due to in-
sufficient voltage. You can change this value in the program
group “User settings - low-voltage - cut-off”.
The screen displays the trigger voltage for automatic charge
termination which is set in the “User settings - Delta Peak volta-
ge” menu. The voltage is set separately for NiCd and NiMH
batteries, and the figure is stated in mV per cell.
The screen displays the initial charge program which is set in
the program group “User settings - power-on settings”, together
with the initial charge current.
The charger is now ready for use.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
l o w v o l t a g e
c u t o f f = 1 1 . 8 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ N i C d d e l t a - N i M H
2 0 m V p e a k 1 5 m V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i C d a u t o m a t i c
C : 2 . 5 A l i m i t e d
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ S i c h e r h e i t s t i m e r
1 2 0 m i n .
The screen displays the maximum charge time for NiCd and
NiMH batteries which is set in the “User settings - safety timer”
menu.
NiCd
AUTOMATIC-
program
MODE
ENTER
MODE
NiMH
AUTOMATIC-
program
ENTER
ENTER
ENTER
User
settings
MODE
MODE
Pb
AUTOMATIC-
program
ENTER
MODE
Lithium
MANUAL-
program
2 sec.
2 sec.
2 sec.
2 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
G r a u p n e r
U L T R A M A T 2 5
7. Program flowchart
6. Charge and discharge programs „Akku“
The various facilities of the charger are divided up into four program groups which you can select by
pressing the
ENTER button. The sequence is shown in the flow chart below.
Note : If a battery is connected to the charger, it is not possible to switch to a different program group.
This is an intentional safety feature, designed to make it impossible to switch accidentally to a charge
program which is unsuitable for the battery in question when a charge process is actually in progress.
You can interrupt the charge process at any time by pressing the “MODE” button.
Ni-Cd battery programs: recharge, condition, balance, discharge to measure capacity or residual
capacity, or select cells.
Ni-MH battery programs: recharge, discharge to measure capacity or residual capacity, or select cells.
LiIo / LiPo battery programs: Charge, discharge to determine capacity, residual capacity, and cell
selection.
Lead-acid programs: recharge, discharge to measure capacity or residual capacity, trickle charge for
stand-by operation.
User settings: determine the basic functions of the charger, and set individual parameters within the
various charge programs.
NiCd
AUTOMATIC-
program
MODE
MODE MODE MODE MODE
Initial-
program
NiCd
NiMH
Lithium
Pb
NiCd -
∆∆∆∆∆
Peak
- 10 mV
.
.
- 30 mV
NiMH -
∆∆∆∆∆
Peak
- 5 mV
.
.
- 25 mV
Car battery
cut-off
- 10,5 Volt
- 11.8 Volt
Button click
- O F F
- ON
Summer
- O F F
- 10 sec.
- no limit
Erase
user
settings
**erased**
Initial
current
NiCd 0,1... 5A
NiMH 0,1... 5A
Lith. 0,1... 5A
Pb 0,1... 5A
or automatic current
ENTER
MODE
User-
settings
NiCd
MANUAL-
program
NiCd
discharge-
program
NiCd
conditioning-
program
NiCd
capacity test-
program
NiCd
balacing-
program
MODE MODE MODE MODE MODE
MODE MODE MODE MODE
NiCd / NiMH
safety-
timer
10 ... 300 min.
NiCd / NiMH
charge
termin delay
AUS,
0...9 min.
ENTER
NiMH
AUTOMATIC-
program
MODE MODE MODE
NiMH
capacity test-
program
NiMH
MANUAL-
program
ENTER
ENTER
MODE MODE MODE
MODE
Pb
AUTOMATIC-
program
Pb
MANUAL-
program
Pb
discharge-
program
Pb
capacity test-
program
ENTER
MODE MODE MODE MODE
Lithium
MANUAL-
program
Lithium
discharge-
program
Lithium
capacity test-
program
Lithium
type-
select
NiMH
discharge-
program
MODE
NiCd
cycle count
MODE
MODE
MODE
Pb
trickle-
charge
MODE
max.-
current
NiCd 0,1... 5A
NiMH 0,1... 5A
Pb 0,1... 5A