GRAUPNER 6478 Скачать руководство пользователя

Страница: 6 / 55

Page

6/55

•

Connect the battery to be charged to the charger output sockets using a suitable charge lead (red =

positive terminal, black = negative terminal).

•

Be sure to read the information provided by the battery manufacturer regarding charging methods,

and observe the recommended charge currents and charge times. Do not attempt to fast-charge

batteries unless they are expressly stated to be suitable for the high currents which this charger

delivers.

•

Please bear in mind that new batteries do not reach their full capacity until they have undergone

several charge / discharge cycles. You should also be aware that the charger may terminate the

charge process prematurely when connected to new packs, and batteries which have been deep-

discharged.

•

A Ni-Cd pack will normally be warm at the end of a rapid-charge process, but if you notice that one

cell of the pack is much hotter than the others, this may well indicate a fault in that cell. Such packs

could fail completely without warning, and should not be used again. Dispose of the battery safely,

preferably taking it to a toxic waste disposal centre.

•

Ensure that all connectors and terminal clamps make good, sound contact. For example, if there is a

brief interruption due to an intermittent contact, the result is inevitably a malfunction such as a restart

of the charge process, which would result in the pack being massively overcharged.

•

A common cause of malfunctions is the use of unsuitable charge leads. Since the charger is

incapable of detecting the difference between a pack’s internal resistance, cable resistance and

connector transfer resistance, the first requirement if the charger is to work perfectly is that the

charge lead should be of

adequate

conductor cross-section and should be

not be more than

30 cm long

Good-quality connectors (gold-contact types) must be fitted to both ends.

• Charging transmitter batteries

A battery installed in a radio control transmitter can usually be recharged via the integral charge

socket which is fitted to the transmitter itself. Transmitter charge sockets generally include a diode

which prevents reverse current flow. This prevents damage to the transmitter electronics should the

charger be connected with reverse polarity, or if a short-circuit occurs between the bare ends of the

charge lead connectors. However, a transmitter battery protected in this way can only be charged by

the CHARGER if the diode is by-passed. Please read your transmitter operating instructions for

information on how to do this. The stated maximum charge current for the transmitter battery must

never

be exceeded. To avoid possible damage to the internal transmitter components due to

overheating and heat build-up, we recommend that the battery should be removed from the

transmitter’s battery compartment prior to charging. The transmitter must be set to „

OFF

“ and left in

that state for the

whole

period of the charge process.

Never

switch a radio control transmitter on when it is still connected to the battery charger. The

slightest interruption in the charge process may allow the charge voltage to rise to the point where it

immediately

ruins the transmitter.

Never

attempt to carry out any battery discharge or battery maintenance programs via the

Содержание 6478
























































Результаты поиска

Содержание 6478

Отзывы:

Похожие инструкции для 6478

Бренды по названию

Популярные бренды

GRAUPNER 6478, Руководство по эксплуатации

Результаты поиска

Содержание 6478

Отзывы:

Похожие инструкции для 6478

Бренды по названию

Популярные бренды