GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 295

Страница: 295 / 338

295

UCP

3901

Multiviewer SDC

Chapter

User Manual

The configuration of this page is the same as for Essence Processing. See

Loopback Router

on page 162.

Setup

The

Setup

page displays basic information about the Multiviewer SDC, such as the serial

number and software build number. This information may be required by Grass Valley

Support if technical assistance is needed. Use the functions on the page to restart the card

or to return all settings to their factory or default settings.
The configuration of this page is the same as for Essence Processing. See

Setup

, on

page 163.

Ethernet Gb

For a UCP

3901:

• The

Ethernet Gb

page shows details and status for the

MANAGEMENT

Ethernet

connector port found on the card’s rear panel. See

Rear Panel and Connectors

, on

page 32.

• The UCP

3901 defaults to use DHCP for the

MANAGEMENT

Ethernet port address

negotiation, but this can be overridden and a static IP address can be specified if

required.

• The management port handles card configuration and upgrade, as well as NMOS IS-04

and IS

05 communications with the NMOS registry.

• The Ethernet configuration for this port can also be set through the frame’s control

panel. This is useful when the card is first installed in the frame, to make it quickly

operational. See

Local control using the Densité frame control panel to set the Card’s IP

Addresses

, on page 38.

For a IQUCP25 / IQUCP50:

• The

Ethernet Gb

page displays details and the status of the ‘card front’ Ethernet port of

the IQUCP25 / IQUCP50 card. This is for Grass Valley engineering use only.

• The IQUCP25 / IQUCP50 defaults to use DHCP for the ‘card front’ Ethernet port address

negotiation, but this can be overridden and a static IP address can be specified if

required.

The configuration of this page is the same as for Essence Processing. See

Ethernet Gb

, on

page 165.
See

Ethernet Pages 1 and 2

, on page 288 to configure the media Ethernet configurations.

Interop

The

Interop

page allows certain parameters to be changed in order to improve

interoperability with third-party equipment, including disabling extended headers, and

setting payload types.
The configuration of this page is the same as for Essence Processing. See

Interop

, on

page 168.

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды