GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 288

Страница: 288 / 338

288

Multiviewer SDC

FEC

FEC

The FEC page allows Forward Error Correction (FEC) Clause 74 (FC) and Clause 108 (RS)

functionality of IEEE 802.3

to be enabled. FEC performance logging and statistics are also

available. The FEC to be used is selected through the Card Firmware/Software Version

options on the Configuration page; see

Configuration

, on page 281 for more information.

The configuration of this page is the same as for Essence Processing. See

FEC

, on page 94.

NMOS

The

NMOS

page allows various NMOS parameters to be set, allowing the UCP

3901 to inter-

operate with other equipment through an NMOS registry. NMOS must be used with SMPTE

ST 2110 stream transport only.
The configuration of this page is the same as for Essence Processing. See

NMOS

, on

page 96.

Ethernet Pages 1 and 2

Ethernet 1

and

Ethernet 2

are the Multiviewer’s high speed media ports.

Ethernet 1

identified as

SFP1

and

Ethernet 2

is identified as

SFP2

on the card’s rear panel. See

Rear

Panel and Connectors

, on page 32.

The

Ethernet

pages show details and status for each of the Multiviewer’s high speed media

network interfaces. The UCP

3901 defaults to use DHCP for Ethernet port address

negotiation, but this can be overridden and a static IP address can be specified if required.
The Ethernet configuration for these ports can also be set through the frame’s control

panel. This is useful when the card is first installed in the frame, to make it quickly

operational. See

Local control using the Densité frame control panel to set the Card’s IP

Addresses

, on page 38.

See

Ethernet Gb

, on page 295 for information on the

MANAGEMENT

/ IQ modular chassis

Ethernet connector.
The configuration of this page is the same as for Essence Processing. See

Ethernet Pages 1

and 2

, on page 101.

3.Ensure the network switch you plan to use supports CL91-RS-FEC. For example, for Cisco products, see

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/kb/b_Cisco_ACI_and_Forward_
Error_Correction.html

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды