Graphite 58G014, Инструкция по эксплуатации

Страница: 13 / 92

13
9.
LED diodes
10.
Button for battery level indication
11.
Battery level indicator (LED)
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1.
Dust bag - 1 pce
2.
Abrasive paper - 1 pce
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Push battery lock button ( 6 ) and slide out the battery ( 7 )
( fig. A ).
• Insert charged battery ( 7 ) into the handle holder, you should
hear when the battery lock button ( 6 ) snaps.
BATTERY CHARGING
The device is supplied with partially charged battery. The battery
should be charged in ambient temperature between 4°C and
40°C. New battery, or one that has not been used for a long
time, will reach full efficiency after approximately 3 to 5 charge/
discharge cycles.
• Remove the battery ( 7 ) from the device ( fig. A ).
• Connect the charger to mains socket ( 230 V AC ).
• Slide the battery ( 7 ) into the charger ( 8 ) ( fig. B ). Ensure the
battery is properly fitted (pushed to the end).
When the charger is connected to a mains socket ( 230 V AC ), the
green diode ( 9 ) on the charger turns on to indicate connected
supply.
When the battery ( 7 ) is placed in the charger ( 8 ), the red diode
( 9 ) on the charger turns on to indicate that the charging is in
progress.
At the same time green diodes ( 11 ) of the battery level indication
are flashing in different configurations, see description below.
• All diodes are flashing - battery is empty and requires
charging.
• 2 diodes are flashing - the battery is partially discharged.
• 1 diode is flashing - the battery level is high.
Once the battery is charged, the diode ( 9 ) on the charger lights
green, and all battery level diodes ( 11 ) light continuously. After
some time (approx. 15 s) battery level indication diodes ( 11 ) turn
off.
Do not charge the battery for more than 8 hours. Exceeding
this time limit may cause damage to battery cells. The charger
will not turn off automatically when the battery is full. Green
diode on the charger will remain on. Battery level indication
diodes turn off after some time. Disconnect power supply
before removing the battery from the charger socket. Avoid
consecutive short chargings. Do not charge the battery after
short use of the tool. Significant decrease of the period
between chargings indicates the battery is worn out up and
should be replaced.
Batteries heat up when charging. Do not operate just
after charging – wait for the battery to cool down to room
temperature. It will prevent battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with signalisation of the battery level (3
LED diodes) (
11 ). To check battery level status, press the button
for battery level indication ( 10 ) ( fig. C ). When all diodes are lit,
the battery level is high. When 2 diodes are on, the battery is
partially discharged. When only one diode is lit, the battery is
discharged and must be recharged.
CHOOSING SANDING PAPER
Coarse-grained sanding paper is used for coarse processing of most
materials, while fine-grained paper is used for finishing works.
• When the surface is not flat, start the work with coarse-grained
sanding paper and continue until the surface is flat.
• Next use middle-grained paper to remove traces of coarse
processing.
• To finish the work use fine-grained sanding paper.
INSTALLING SANDING PAPER
The orbital sander is equipped with pad with hook-and-loop
fastener. Use only appropriate sanding paper (perforated).
• Put the sanding paper close to the sander backing pad ( 5 ).
• Place the sanding paper so its holes ( a ) match holes on the sander
backing pad.
• Press the sanding paper against the backing pad ( 5 ) ( fig. D ).
• Ensure that the holes on the sanding paper and backing pad fully
match; it ensures sufficient dust extraction.
DUST EXTRACTION
Equipment of orbital sander includes dust bag ( 3 ) to maintain the
processed surface clean.
• Slide the dust bag ( 3 ) fastening onto dust extraction outlet ( 4 )
( fig. E ).
• When the dust bag is full, empty it to a special container.
• Reinstall the dust bag on the dust extraction outlet.
• Make sure the dust bag is securely fastened on the outlet.
Emptying the bag when it is half-full is recommended.
DUST BAG EMPTYING
The dust bag is placed on the plastic casing. Slightly turn the rear
ring counter-clockwise and slide it off from the back plastic casing to
empty the dust bag (fig. F). Remove the contents from the dust bag.
Installation of the dust bag is similar to removal, only the sequence
of actions is reversed.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The orbital sander features 3 gears (ranges of rotational speed).
Subsequent pressing of the switch button cycles between
rotational speeds.
Switching on:
Press the switch button (2) – the sander starts operation at the
maximum rotational speed.
Next press of the switch button – the sander operates at the
moderate rotational speed.
Next press of the switch button – the sander operates at the lowest
rotational speed.
Switching off:
Press the switch button (1) (fig. G).
Regardless of the gear the sander operates when switched off,
after it is switched on again, it starts operation at the highest
speed and cycles 3-2-1 (from the highest to the lowest rotational
speed, as described above).