Graphite 58G014, Инструкция по эксплуатации

Страница: 14 / 92

14
ORBITAL SANDER OPERATION
• Whole area of the backing pad must rest on the processed surface.
• Turn the sander on, select appropriate rotational speed and
apply moderate pressure; move it along the processed material in
circular movements, in transverse or lengthwise direction.
• For coarse processing use sanding paper with coarse grain, for
finishing processing use fine-grained paper. It is best to match the
type of sanding paper by trials and errors.
• To end polishing, reduce pressure, lift the sander above the
processed surface and only then you can switch off the tool.
OPERATION AND MAINTENANCE
Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with compressed
air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
REPLACEMENT OF BACKING PAD
Damaged backing pad ( 5 ) must be replaced immediately.
• Unscrew the screws that fix the backing pad (5).
• Remove and replace the backing pad.
• Tighten the fixing screws.
All defects should be repaired by service workshop authorized
by the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless Orbital Sander
Parameter Value
Battery voltage 18 V DC
Range of idle rotational speed 5000/7000/9000 min -1
Range of Idle oscillation speed 10000/14000/18000 min -1
Oscillation amplitude 2,7 mm
Pad dimensions 125 mm
Size of sanding paper 125 mm
Protection class III
Weight 1,135 kg
Year of production 2017
Graphite System Battery
Parameter Value
Battery 58G001 58G004
Battery voltage 18 V DC 18 V DC
Battery type Li-Ion Li-Ion
Battery capacity 2000 mAh 4000 mAh
Ambient temperature range 4 0 C – 40 0 C 4 0 C – 40 0 C
Charging time for charger 58G002 1 h 2 h
Weight 0,400 kg 0,650 kg
Year of production 2017 2017
Graphite System Charger
Parameter Value
Charger type 58G002
Supply voltage 230 V AC
Power supply frequency 50 Hz
Charging voltage 22 V DC
Max. charging current 2300 mA
Ambient temperature range
4 0 C – 40 0 C
Charging time of the battery 58G001
1 h
Charging time of the battery 58G004
2 h
Protection class
II
Weight
0,300 kg
Year of production
2017
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information
Parameters of produced noise level, such as sound pressure level
Lp
A
and sound power level Lw
A
with measurement uncertainty K
are specified below in this manual, in compliance with EN 60745.
Vibration values a
h
and measurement uncertainty K are
determined in accordance with EN 60745-2-1 and specified
below.
Vibration level specified below in this manual was measured in
accordance with measurement procedure defined in EN 60745
and can be used to compare power tools. It can also be used for
initial assessment of exposure to vibrations.
Specified vibration level is representative for main applications
of the power tool. Vibration level may change if the power tool is
used for other purposes, with different working tools or will not
be maintained properly. The abovementioned factors may lead
to higher exposure to vibrations during whole working time.
To precisely define exposure to vibrations, include periods when
the power tool is switched off and when it is switched on but
not used for working. This way total exposure to vibrations may
be significantly lower. Use additional safety measures to protect
the user against results of exposure to vibrations, such as: power
tool and working tool maintenance, proper hand temperature
conditions, good work organisation.
Sound pressure level: Lp
A
= 80,2 dB (A) K=3dB (A)
Sound power level: Lw
A
=91,2 dB (A) K=3dB (A)
Vibration acceleration value:
a
h
= 7,521 m/s 2 K= 1,5 m/s 2