background image

section 16: Guarantee

Page 65

• 

Instances where the heat pump has been un-installed and 

re-installed in another location.

• 

Use of spare parts not authorised by Grant Engineering (UK) 

Limited.

• 

Consumable items including, but not limited to, antifreeze and 

biocide inhibitor.

terms of manufacturer’s guarantee

• 

The Company shall mean Grant Engineering (UK) Limited.

• 

The heat pump must be installed by a competent installer 

and in full accordance with the relevant Codes of Practice, 

Regulations and Legislation in force at the time of installation.

• 

The heat pump is guaranteed for two years from the date of 

installation⁴, providing that after twelve months the annual 

service has been completed³ and the heat pump registered 

with the Company within thirty days of the installation date4. 

Any work undertaken must be authorised by the Company and 

carried out by a competent service engineer.

• 

The internal heat exchanger of the heat pump is also covered 

by a two year parts and labour guarantee from the date of 

installation⁴. This is subject to the following:

o  The heat pump is operated correctly, in accordance with 

the installation and servicing instructions.

Proof is provided that the system has been flushed or 

chemically cleaned where appropriate (refer to BS 7593) 

and that the required quantity of a suitable corrosion 

inhibitor added.

o  Proof of annual servicing (including the checking of any 

expansion vessels and pressure relief valves) must 

be provided if and when requested by the Company. 

ImPortAnt

 Grant Engineering (UK) Limited 

strongly 

recommends

 that a Grant Mag-One in-line magnetic 

filter/s (or equivalent⁵) is fitted in the heating system 

pipework. This should be installed and regularly serviced 

in accordance with the filter manufacturer’s instructions.

• 

This guarantee does not cover breakdowns caused by 

incorrect installation, neglect, misuse, accident or failure to 

operate the heat pump in accordance with the manufacturer’s 

installation and servicing instructions.

• 

The heat pump is registered with the Company within thirty 

days of installation. Failure to do so does not affect your 

statutory rights¹.

• 

The balance of the guarantee is transferable providing the 

installation is serviced prior to the dwelling’s new owners 

taking up residence. Grant Engineering (UK) Limited must be 

informed of the new owner’s details.

• 

The Company will endeavour to provide prompt service in 

the unlikely event of a problem occurring, but cannot be held 

responsible for any consequences of delay however caused.

• 

This guarantee applies to Grant Engineering (UK) Limited 

air source heat pumps purchased and installed on the UK 

mainland, Isle of Wight, Channel Islands and Scottish Isles 

only². Provision of in-guarantee cover elsewhere in the UK is 

subject to agreement with the Company.

• 

All claims under this guarantee must be made to the Company 

prior to any work being undertaken. Invoices for call out/repair 

work by any third party will not be accepted unless previously 

authorised by the Company.

• 

Proof of purchase and date of installation, commissioning and 

service documents must be provided on request.

• 

If a replacement heat pump is supplied under the guarantee 

(due to a manufacturing fault) the product guarantee continues 

from the installation date of the original heat pump, and not 

from the installation date of the replacement⁴.

• 

The replacement of a heat pump under this guarantee does 

not include any consequential costs.

foot notes

1.  Your statutory rights entitle you to a one year guarantee period 

only.

2.  The UK mainland consists of England, Scotland and Wales 

only. Please note that for the purposes of this definition, 

Northern Ireland, Isle of Man and Scilly Isles are not 

considered part of the UK mainland.

3.  We recommend that your air source heat pump is serviced 

every twelve months (even when the guarantee has expired) 

to prolong the lifespan and ensure it is operating safely and 

efficiently.

4.  The guarantee period will commence from the date of 

installation, unless the installation date is more than six 

months from the date of purchase, in which case the 

guarantee period will commence six months from the date of 

purchase.

5.  As measured by gauss. The Mag-One magnetic filter has a 

Gauss measurement of 12000.

Version 1.1 - February 2017

Содержание Aerona3 HPID12R32









































































Отзывы: