background image

Section 4: Electrical

Page 13

OVER-TEMPERATURE CUT-OUT

This immersion heater is fitted with a Cotherm type TSR 

thermostat that incorporates an independent non-self-

resetting over-temperature cut-out to prevent excessive water 

temperatures.
The reset pin is located in a small opening to the side of the 

control dial and indicated by small triangle with the word ‘safety’. 

Refer to Figure 4-3. 
In normal operation the reset pin will be approximately 2-3mm 

below the surface of the plastic thermostat housing. 

Should the over-temperature cut-out operate, the reset pin will be 

pushed up to become level or slightly above the surface of the 

housing.

To reset the over-temperature cut-out:

• 

Isolate the volumiser / immersion element from the mains 

electrical supply.

• 

Wait for the temperature in the volumiser to fall sufficiently.

• 

Using a suitably sized implement, push the reset pin using 

hand pressure only to return it to its normal operating 

position.

! WARNING !

Ensure the volumiser / immersion heater is isolated from 

the mains before attempting to reset to 

over-temperature cut-out.

If the immersion heater needs to be replaced it must be fitted to 

the volumiser using the gasket provided on the unit. Only use a 

correctly shaped spanner. Stilsons or pipe grips should NOT be 

used. The use of sealing compound is not recommended.

! WARNING !

Always ensure that the immersion heater cap is not 

covered.

Содержание Aerona3 HPID10R32





















Отзывы: