Gram Gastro 07/08 Скачать руководство пользователя страница 29

 
 

 

 

29 

Settings for running cycle 

 
Push on   and   buttons at the same time in more than 6 sec. and the menu item [ 

] appears in the display. 

 
With   and   buttons it’s possible to look through the main menu item [ 

],

 

] and [ 

]. Push on   button to enter 

the submenu from the main menu items. 
With   and   buttons it’s possible to look through the submenus menu items. Push on   button to enter the desired 
menu item and adjust the setting with   and    buttons. 
 
To confirm the new setting, push   button. Leave the submenu and main menu item with the   button. 
 

Menu access P+3 

 

 

 

 

 

 

Compressor setup 

C1 

[° K] 

Differential for compressor cut-in and cut-out. 

 

 

C2 

[° C] 

Highest allowed  temperature limit for the cabinet. 

C3 

[° C] 

Lowest allowed temperature limit for the cabinet.

C4 

[min]  Forced pause time for compressor between cut-out and cut-in. 

C5*   

Number of condenser sensors connected. 

C6*  [min]  Compressor stop by open door. 
C7*  [° K] 

Soft differential for cool/heat cut-out (kelvin) 

C8*  [° C] 

Setpoint for condenser fan

C9*  [° K] 

Cut-out differential for condenser fan (kelvin)

Evaporator fan 

F1*  [° C] 

Temperature allowing the evaporator fan to start after defrosting. 

 

 

F2 

[min.]  Pause time of evaporator fan, while the compressor is stopped. 

F3 

[sek.]  Running time of evaporator fan, while the compressor is stopped. 

F4*  [° K] 

Stop temp. of LT compressor i cascade evaporator (celcius) 

Display presentation  d 

d1 

 

Number of defrosts  / 24h

 

 

d2 

[° C] 

Defrost stop temperature measured at the evaporator.

d3 

On/off 

Activation of defrost by start-up sequence [1=on / 0=off]. 

d4*  [min.] 

Maximum defrosting  time. 

d5*   

Selection between automatic- [1], air- [2] or electric defrosting [3]. 

d6*  [min.] 

Dripping time after defrosting

d7*  [° C] 

Temperature limit deciding the defrosting method, when d5 = [1] 

d8*  [° C] 

Evaporator temperature starting an extra defrosting cycle. 

d9*   

Defrosting after chilling (process) 

 

*Might not be available, be available at limited or full extent, depending on programme variant and product. 
 

 

 

 

Содержание Gastro 07/08







































Отзывы: