Grady-White Boats Seafarer 228 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 66

Grady-White Boats Seafarer 228 Скачать руководство пользователя страница 54

8-2

Chapter 8: Seafarer 228

•

Horn

The horn meets the requirements of the USCG for sounding devices.

•

Livewell (optional)

This switch activates the livewell system.

•

Navigation/Anchor Lights

This three-position switch (NAV-OFF-ANC) changes the lighting configurations to running
or anchor lights.

•

Raw Water

This switch activates the raw water washdown system.

•

Wiper

This switch powers the windshield wiper(s). The starboard wiper is standard while the
port wiper is optional.

•

Accessory

Switches and breakers labeled “ACC” are blank. They may be used for non-factory
installed accessories. Switch labels are available from your dealer for non-factory
installed options.

Other Switches

•

Trim/Tilt

The trim/tilt switch is located on the throttle control. Trim changes the angle of thrust of
the engine (reference “Trim” on page 4-1). Tilt raises the drive unit for trailering.

•

Trim Tab

These switches control the hydraulic trim tabs used for adjusting the attitude of the boat.
See “Trim Tabs” on page 8-8 for more details.

N OT I C E

Use anti-corrosion spray on the back of panels and on exposed wires to prevent corrosion that
could lead to an electrical system failure.

«
...
52
53
54
55
56
...
»

Содержание Seafarer 228



































































Отзывы:

Нет отзывов