Grady-White Boats Seafarer 228 Скачать руководство пользователя страница 41

6-7

Chapter 6: Maintenance and Service

Fuel System

To determine whether a fuel flow problem is in your fuel system or your engine, follow this 

simple method. Connect a portable tank to the engine and operate the engine. If the problem 
persists, the likely cause is with the engine itself. If the problem goes away, the source must be in 
the boats’ fuel system. One component that should be inspected if a restriction occurs is the anti-
siphon valve. If fuel does not flow properly through this part, it must be cleaned and/or replaced.

  W A R N I N G

Do not remove the anti-siphon valve and replace with a regular barb. Modification or removal of 
the anti-siphon valve could allow a dangerous accumulation of fuel and vapors in the hull in the 
event of a fuel system leak.

Annually conduct a detailed inspection of fuel system components, especially those hidden 

from routine inspection. Replace any fittings, deteriorated hoses, clamps or connections 
immediately. Fuel filter/water separators should be replaced at least annually. 

Содержание Seafarer 228



































































Отзывы: