Grady-White Boats Freedom 375 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 86

Grady-White Boats Freedom 375 Скачать руководство пользователя страница 56

8-2

Chapter 8: Freedom 375

•

Hardtop Lights

This momentary switch activates the multi-colored recessed downlights. Depressing the
switch one time turns the lights on. Subsequent pressing of the switch will cycle the
lights through the colors. Press and hold for 3 seconds to turn lights off.
Note: Depressing/cycling the switch too quickly may cause the light colors to be
unsynchronized. Turn the lights off to reset the light colors.

•

Horn

The horn meets the requirements of the USCG for sounding devices.

•

Livewell

This switch activates the livewell pump and light.

•

Navigation/Anchor Lights

This three-position switch (NAV-OFF-ANC) changes the lighting configurations to running
or anchor lights.

•

Raw Water

This switch activates the raw water washdown system.

•

Spreader Lights

This switch activates the hardtop spreader lights.

•

Sunroof

This switch operates the sunroof. Depress the bottom of the switch to open the sunroof
and the top of the switch to close the sunroof.

•

Underwater Lights

This switch activates the underwater lights.

•

Windlass

This switch operates the anchor windlass. Depress the top of the switch to raise the
windlass and the bottom of the switch to lower the windlass.

•

Wiper

This switch powers the windshield wipers and washers.

•

Accessory

Switches and breakers labeled “ACC” are blank. They may be used for non-factory
installed accessories. Switch labels are available from your dealer for non-factory
installed options.

N OT I C E

Use anti-corrosion spray on the back of panels and on exposed wires to prevent corrosion that
could lead to an electrical system failure.

Other Switche

s

•

Trim/Tilt

The trim/tilt switch is located on the throttle control. Trim changes the angle of thrust of
the engine (reference "Trim" on page 4-1). Tilt raises the drive unit for trailering.

«
...
54
55
56
57
58
...
»

Содержание Freedom 375























































































Отзывы:

Нет отзывов