Graco Ultimate Mx695 Скачать руководство пользователя страница 19

Страница: 19 / 36

General Repair Information

WARNING

INJECTION HAZARD
To reduce the risk of serious injury, when
instructed to relieve pressure, follow the
Pressure Relief Procedure on page 8.

Tool List

These service tools are required.

12” adjustable wrench:

pump

1/4” Allen

wrench:

filter plug

3/8” Allen

wrench:

pump manifold

3/16” Allen

wrench:

gear housing, legs, handle

5/64” Allen

wrench:

pressure adjustment knob

Phillips

screwdriver:

junction box, front cover

, motor

shield
3/8” socket wrench:

motor mount

5/8” socket wrench:

drain valve, on/off switch boot,

piston
5/8” open end wrench:

outlet fittings

13/16” socket wrench:

drain valve

1-1/4” socket wrench:

pump inlet valve

1/2” open end wrench:

pump rod

11/16” open end wrench:

piston jam nut

15/16” open end wrench:

flats of inlet tube

1-3/4” open end wrench:

pump jam nut

5/64” drive pin:

drain valve pin

3” needle nose pliers:

wiring, on/off switch

Hammer & punch:

packing nut

Torque wrenches:

various fasteners

Pipe wrench:

suction tube

CAUTION

To reduce the risk of a pressure transducer malfunc-
tion, properly mate connectors and never pull on a
wire to disconnect it.

When disconnecting wires, use needle nose
pliers to separate mating connectors.

When reconnecting wires, center flat blade of
male connector in blade of female connector.

Route wires carefully and avoid pinching any
wires between covers.

CAUTION

Improper wire routing can result in poor sprayer
performance or damage to the pressure transducer.

Keep all screws, nuts, washers, gaskets, and
electrical fittings removed during repair proce-
dures.

Test your repair before regular operation to be
sure problem is corrected.

If sprayer does not operate properly, verify that
everything was done correctly. Also refer to Trou-
bleshooting Guide, page 14, to help identify other
possible problems and solutions.

WARNING

MOVING PARTS HAZARD
To reduce the risk of serious injury, in-
cluding electric shock, DO NOT touch
any moving parts or electrical parts with

your fingers or a tool while inspecting the sprayer.

Shut off the sprayer and unplug it as soon as you
complete the inspection.

Reinstall all covers, gaskets, screws and washers
before operating the sprayer.

WARNING

FIRE HAZARD
During operation, the motor and drive
housing become very hot and could burn
your skin if touched. Flammable materi-

als spilled on the hot, bare motor could cause a fire
or explosion.

Содержание Ultimate Mx695





































Результаты поиска

Содержание Ultimate Mx695

Отзывы:

Похожие инструкции для Ultimate Mx695

Бренды по названию

Популярные бренды

Graco Ultimate Mx695, Руководство пользователя

Результаты поиска

Содержание Ultimate Mx695

Отзывы:

Похожие инструкции для Ultimate Mx695

Бренды по названию

Популярные бренды