Graco Ultimate Mx695 Скачать руководство пользователя страница 18

Страница: 18 / 36

Intermediate Problem Solving

TYPE OF
PROBLEM

WHAT TO CHECK
If check is OK, go to next check

WHAT TO DO
When check is not OK, refer to this column

Spray Pattern
Variations
(continued)

3. Check pressure adjustment potentiometer (77) by

replacing it with a new one.

(continued)

4. Check Low Output section, page 16.

Motor Is Hot and
Runs Intermittently

1. Determine if sprayer was operated at high pressure

with small tips, which causes excessive heat build
up.

1. Decrease pressure setting or increase tip

size.

2. Be sure ambient temperature where sprayer is lo-

cated is no more than 90

F (32

C) and sprayer is

not located in direct sun.

2. Move sprayer to shaded, cooler area if

possible.

3. Check motor.

3. Replace motor. See page 23.

Building Circuit
Breaker Opens As
Soon As Sprayer
Switch Is Turned
O

1. Check all electrical wiring for damaged insulation,

and all terminals for loose fit or damage.
Also check wires between pressure transducer
and motor. See page 23.

1. Repair or replace any damaged wiring or

terminals. Securely reconnect all wires.

Switch Is Turned
On.

2. Check for missing motor brush inspection plate

gasket (see page 21), bent terminal forks or other
metal to metal contact points which could cause a
short.

2. Correct faulty conditions.

3. Check motor armature for shorts. Use an

armature tester (growler) or perform motor test.
See page 18. Inspect windings for burns.

3. Replace motor. See page 23.

4. Check motor control board (22a) by performing

motor control board diagnostics on page 24. If
diagnostics indicate, substitute with a good board.

CAUTION: Do not perform this check until motor
armature is determined to be good. A bad motor
armature can burn out a good board

4. Replace board. See page 24.

Circuit breaker
opens after sprayer
operates for 5 to 10
minutes.

1. Check ‘Basic Problems – Electrical’ on page 14.

Building circuit
breaker opens as
soon as sprayer is
plugged into outlet
and sprayer is NOT
turned on.

1. Check ON/OFF switch (80). Be sure sprayer is

unplugged! Disconnect wires from switch. Check
switch with ohmmeter. The reading should be
infinity with ON/OFF switch OFF, and zero with
switch ON.

CAUTION: A short in motor circuit can damage
switch and or motor control board (22a).

1. Replace ON/OFF switch. See page 25.

2. Check for damaged or pinched wires in junction

box (20).

2. Replace damaged parts.

Unit will not run on
generator but does
run on AC power

1. Check the generator’s “peak” voltage. This sprayer

will not run if the peak voltage is above 190V or
below 100V.

1. Use AC power or a different generator.

Содержание Ultimate Mx695





































Результаты поиска

Содержание Ultimate Mx695

Отзывы:

Похожие инструкции для Ultimate Mx695

Бренды по названию

Популярные бренды

Graco Ultimate Mx695, Руководство пользователя

Результаты поиска

Содержание Ultimate Mx695

Отзывы:

Похожие инструкции для Ultimate Mx695

Бренды по названию

Популярные бренды