manualshive.com logo in svg

Graco TexSpray 248091, Операция и комплектующие

Поделиться
Скачать
Graco TexSpray 248091 Скачать руководство пользователя страница 16

Troubleshooting 

16

Troubleshooting

Problem

Cause

Solution

Material will not flow out of gun

Material too thick

Thin material. Increase pressure at 
pump.

Not enough air

Open gun air valve (A) more 
(counter-clockwise)

Trigger adjustment set too low

Rotate trigger nut clockwise to 
increase (adjust) trigger travel

Nozzle too small

Increase nozzle size

Gun is plugged

Clean gun

Pattern too fine

Material too thin

Add more dry material to mix to 
thicken

Air pressure too high

Close gun air valve (A) partially 
(clockwise)

Gun needle travel too low

Rotate trigger nut clockwise to 
increase (adjust) trigger travel

Nozzle too small

Replace nozzle with larger size

Pattern too coarse

Material too thick

Add water to mix to thin material

Air pressure too low

Open gun air valve (A) more 
(counter-clockwise)

Nozzle too large

Replace nozzle with smaller size

Gun will not shut off

Worn nozzle and/or needle

Relieve pressure

, page 5. Replace 

worn parts

Nozzle retaining ring not on all the 
way

Tighten completely.

Debris in gun passages

Relieve pressure

, page 5. Clean 

gun.

Fluid leaking at flow adjustment nut 
(B)

Damaged seal

Relieve pressure,

 page 5. Replace 

seal (3).

Trigger nut won’t adjust

Dirty threads

Clean threads.

Nozzle not on gun

Put nozzle on gun.

Needle triggered

Adjust when trigger is not pulled.

Air won’t shut off when gun trigger is 
released (non-bleeder model only)

Debris in gun air passages

Relieve pressure

, page 5. Clean 

gun.

Loose air fittings

Tighten air fittings on gun

Worn air seals

Replace air shutoff needle u-cup (4) 
and/or air valve seal (18)

Содержание TexSpray 248091

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды