manualshive.com logo in svg

Graco TexSpray 248091, Операция и комплектующие

Поделиться
Скачать
Graco TexSpray 248091 Скачать руководство пользователя страница 14

Repair 

14

Repair

Fluid Seal Replacement

For Non-bleeder guns use Seal Replacement Kit, 287228.
For Bleeder guns use Seal Replacement Kit, 287338

U

U-cups seals are very fragile. Never pound on 
seal during installation.

1 Remove retaining ring (11), 

nozzle (28), and needle 
assembly (9) through front of 
gun. 

2 Use a hook-shaped object to 

carefully pull up-cup retainer 
and u-cup out of gun.

3 Using your finger or a 1/2-in. 

diameter rod, push new seal 
(3) in place. Make sure seal is 
seated against sleeve bearing 
(35).

4 Insert u-cup retaining ring 

(10). Make sure retiaing ring 
is seated against u-cup (3).

5 Graco recommends you 

replace the entire fluid needle 
assembly at this time, includ-
ing the needle (9) spring (5), 
packing o-ring (6) and guide 
(7).

6 Trigger gun a few times to 

make sure u-cup and retainer 
are securely in place.

ti4445a

ti44

ti4447a

9

5

6

7

ti4813a

Содержание TexSpray 248091

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды