![background image](http://html1.mh-extra.com/html/graco/promix-auto-series/promix-auto-series_service-parts_2253522008.webp)
Glossary of Terms
8
311189L
Glossary of Terms
Air Chop
- the process of mixing air and solvent
together during the flush cycle to help clean the lines
and reduce solvent usage.
Analog
- relating to, or being a device in which data are
represented by continuously variable, measurable,
physical quantities, such as length, width, voltage, or
pressure.
Sequential Color Change
- the process when a color
change is initiated and the system automatically flushes
the old color and loads a new color.
Closed Loop Flow Control
- refers to the process
when the flow rate is adjusted automatically to maintain
a constant flow.
Coriolis Meter
- a non-intrusive flow meter often used in
low flow and light viscosity materials. This meter uses
vibration to measure flow. It is used for non-intrinsically
safe applications.
Digital Input and Output
- a description of data which
is transmitted as a sequence of discrete symbols, most
commonly this means binary data represented using
electronic or electromagnetic signals.
Discrete I/O
- refers to data that constitutes a separate
entity and has direct communication to another control.
Dose Size
- the amount of resin (A) and catalyst (B) that
is dispensed into an integrator.
Dose Time Alarm
- the amount of time that is allowed
for a dose to occur before an alarm occurs.
Ethernet
- a method for directly connecting a computer
to a network or equipment in the same physical location.
Fiber Optic Communication
- the use of light to trans-
fer communication signals.
Fill Time
- the amount of time that is required to load
mix material to the applicator.
Flow Rate Analog Signal
- the type of communication
signal that can be used on the ProControl module.
Flow Rate Tolerance
- the settable percent of accept-
able variance that the system will allow before a flow
rate warning occurs.
Flow Set Point
- a predefined flow rate target.
Grand Total
- a non-resettable value that shows the
total amount of material dispensed through the system.
Intrinsically Safe (IS)
- refers to the ability to locate cer-
tain components in a hazardous location.
Job Total
- a resettable value that shows the amount of
material dispensed through the system for one job. A job
is complete when a color change, purge or complete
system flush occurs.
K Factor
- a value that refers to the amount of material
that passes through a meter. The assigned value refers
to an amount of material per pulse.
Ki
- refers to the degree fluid flow over shoots its set
point.
Kp
- refers to the speed in which the fluid flow reaches
its set point.
Manual Mode
- when the proportioning or flow control
system is controlling the inputs without any input from
an outside control.
Содержание ProMix Auto Series
