Graco magnum pro plus a20 Скачать руководство пользователя

Страница: 56 / 60

Technical Data

332697C

Technical Data

A20

A30

Working pressure range

0-207 BAR, 0-21 Mpa (0-3000 psi)

Electric Motor

4.5A

(open frame, universal)

Operating horsepower

3/8

1/2

Maximum delivery (with tip)

.91 lpm (.24 gpm)

1.02 lpm (.27 gpm)

Paint hose

6.4mm X 7.5 m (1/4 in. x 25 ft)

Maximum tip hole size

0.015 in. (0.38 mm)

Weight, Sprayer only

4.5 kg (10.0 lb)

5.4 kg (12 lb)

Weight, sprayer, hose, & gun

6.0 kg (13.3 lb)

6.9 kg (15.2 lb)

Dimensions (Upright):

Length

35.2 cm (13.8 in)

36.8 cm (14.5 in)

Width

30.7 cm (12.1 in)

31.5 cm (12.4 in)

Height

35.1 cm (13.8 in)

45.5 cm (17.9 in)

Dimensions (Folded):

Length

N/A

Width

N/A

Height

N/A

Power cord

1.0 mm², 3-wire, 1.8 m (6 ft.)

Fluid inlet fitting

1/4 npsm external thread

Fluid outlet fitting

3/4 in. internally threaded

(standard garden hose)

Inlet screen (on suction tube)

1190 micron (16 mesh)

Wetted parts, pump and hose

stainless steel, zinc plated carbon steel, brass, ultra-high molecular weight poly-

ethylene (UHMWPE), Carbide, Nylon, Aluminum, PVC, polypropylene,

fluroelastomer

Wetted parts, gun

aluminum, brass, carbide, nylon, ultra-high molecular weight polyethylene

(UHMWPE), zinc

Generator requirement

1500 Watt minimum

Electrical power requirement

220-240V AC 50/60 Hz, I phase, 10A

Storage temperature range

◆❖

-35° to 71° C (-30° to 160° F)

Operating temperature range

✔

4° to 46° C (40° to 115° F)

◆

When pump is stored with non-freezing fluid. Pump damage will occur if water or latex paint freezes in pump.

❖

Damage to plastic parts may result if impact occurs in low temperature conditions.

✔

Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.

Содержание magnum pro plus a20





























































Результаты поиска

Содержание magnum pro plus a20

Отзывы:

Похожие инструкции для magnum pro plus a20

Бренды по названию

Популярные бренды

Graco magnum pro plus a20, Руководство по ремонту

Результаты поиска

Содержание magnum pro plus a20

Отзывы:

Похожие инструкции для magnum pro plus a20

Бренды по названию

Популярные бренды