Graco Magnum Pro Compact A15 258861 Скачать руководство пользователя страница 4

Warnings 

4

3A0885E

BATTERY HAZARD
The battery may leak, explode, cause burns, or cause an explosion if mishandled. Contents of an open battery 
can cause severe irritation and/or chemical burns. If on skin, wash with soap and water. If in eyes, flush with 
water for at least 15 minutes and seek immediate medical attention.

Do not short-circuit the terminals of the battery.

Keep the battery away from fire.

Charge only with Graco approved charger as listed in this manual.

Do not expose to heat above 170° F (80° C).

Do not expose battery to water or rain.

Do not disassemble, crush, or penetrate the battery.

Follow local ordinances and/or regulations for disposal.

CHARGER ELECTRIC SHOCK, FIRE AND EXPLOSION HAZARD
Improper setup or usage can cause electric shock, fire, and explosion.

Charge only Graco 18V Lithium Ion batteries; other batteries may burst.

Use only in dry locations. Do not expose to water or rain.

If the supply cord is damaged, it must obtained from the manufacturer to avoid a hazard.

Ensure that the outside surface of the battery is clean and dry before plugging into the charger.

Do not attempt to charge non-rechargeable batteries.

Place charger on flat non-flammable surfaces and keep away from flammable materials or fumes when 
recharging battery.

PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical 
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property 
damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids 

containing such solvents.

• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for 

compatibility.

MOVING PARTS HAZARD 
Moving parts can pinch or amputate fingers and other body parts.

Keep clear of moving parts.

Do not operate equipment with protective guards or covers removed.

Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow 
the Pressure Relief Procedure in this manual. Disconnect power.

TOXIC FLUID OR FUMES HAZARD 
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

Read MSDS’s to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating area of 
the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of toxic 
fumes, and burns. This equipment includes but is not limited to:
• Protective eyewear, and hearing protection. 
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

WARNING

WARNING

WARNING

WARNING

Содержание Magnum Pro Compact A15 258861





























Отзывы: