Graco LineLazer 3400 Скачать руководство пользователя

Страница: 43 / 44

Technical Data

3A4587B Operation, Repair, Parts

Technical Data

LineLazer 3400 (Model 25M224)

Metric

Honda GX120 engine
SAE J1995 @ 3600 rpm

4.0 Horsepower

Maximum working pressure

3300 psi

22.8 MPa, 228 bar

Maximum delivery

0.75 gpm

2.84 lpm

Maximum tip size

1 gun with 0.027 in. tip

Inlet paint strainer

12 mesh (893 micron) stainless steel screen, reusable

Outlet paint strainer

60 mesh (250 micron) stainless steel screen, reusable

Pump inlet size

1.0 in. diameter

Fluid outlet size

0.25 in. diameter

Noise Level
Sound power, per ISO 3741

95.4 dBA

Sound pressure, per ISO 3741

91.0 dBA

Vibration, per ISO 5349

Left-hand

260 in/s

6.60 m/s

Right-hand

225 in/s

5.72 m/s

Wetted parts

stainless steel, PTFE, leather, nylon, zinc-plated and

nickel-plated carbon steel, tungsten carbide, chrome

plating, UHMWPE, acetal, polyethylene,

Dimensions (25M224)

Weight (dry, without packaging)

160.0 lb.

72.5 kg

Height Handles Down

39.4 in.

100.0 cm

Height Handles Up

41.3 in.

104.8 in.

Length Handles Down

66.3 in.

168.4 cm

Length Handles Up

68.0 in.

172.7 cm

Width

26.0 in.

66.0 cm

Gun

Maximum Working Pressure

5000 psi

345, 3.45 (bar, MPa)

Weight (with tip and guard)

18 oz.

510 g

Inlet

1/4 npsm male

Maximum material temperature

120°F

50°C

Содержание LineLazer 3400













































Результаты поиска

Содержание LineLazer 3400

Отзывы:

Похожие инструкции для LineLazer 3400

Бренды по названию

Популярные бренды

Graco LineLazer 3400, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer 3400

Отзывы:

Похожие инструкции для LineLazer 3400

Бренды по названию

Популярные бренды