manualshive.com logo in svg

Graco LineLazer 3400, Операция - Ремонт - Запчасти, Страница: 30 / 44

Поделиться
Скачать
Graco LineLazer 3400 Скачать руководство пользователя страница 30

Clutch Housing 

30

3A4587B Operation, Repair, Parts

Clutch Housing

Removal

1. Remove clamp. Do 

Clamp Removal

, page 29.

2. Remove four screws (51) and lock washers (50) 

which hold clutch housing (45) to engine.

3. Remove screw (145) from under mounting plate.
4. Pull off clutch housing (45).

Installation

1. Push on clutch housing (45).
2. Install four capscrews (51) and lock washers (56) 

and secure clutch housing (45) to engine. Torque to 

200 in-lb (22.6 N·m).

3. Install screw (145) from beneath mounting plate. 

Torque to 26 ft-lb (35.2 N·m).

Engine

Removal

NOTE: 

All

 

service to the engine must be performed by 

an authorized HONDA dealer.
1. Remove 

Pinion Assembly/Clutch Arma-

ture/Clamp

 and 

Clutch Housing

, as instructed on 

pages 27, 29 and 30.

2. Disconnect all necessary wiring.
3. Remove two locknuts (111) and screws (110) from 

base of engine. 

4. Lift engine carefully and place on work bench.

Installation

1. Lift engine carefully and place on cart.
2. Install two screws (110) in base of engine and 

secure with locknuts (111). Torque to 20 ft-lb (27.12 

N·m).

3. Connect all necessary wiring.
4. Install 

Pinion Assembly/Clutch Armature/Clamp

 

and 

Clutch Housing

, as instructed on pages 28, 29 

and 30.

ti6322a

145

51

50

45

ti639

0

a

pink

(from engine)

green/yellow

ground

clutch wires

ti6323a

110

111

Содержание LineLazer 3400













































Отзывы:

Нет отзывов