Graco LineLazer 3400 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

Graco LineLazer 3400 Скачать руководство пользователя страница 20

Clean-up

20

3A4587B Operation, Repair, Parts

12. Raise siphon tube above flushing fluid and run striper

for 15 to 30 seconds to drain fluid.

13. Turn pump switch

OFF

. Turn engine

OFF

.

14. Close prime valve. Trigger gun into flushing pail to

purge fluid from hose. Open prime valve.

15. Install filter into filter bowl. Make sure plastic center

tube is tightened securely.

16. Clean Rac Tip, Rac Guard and gasket with a soft

bristle brush to prevent part failure due to dried
materials. Assemble parts and attach loosely onto
gun.

17. Wipe striper, hose and gun with a rag soaked in

water or mineral spirits.

NOTICE

Do not run pump without fluid flow. Damage to

packings can occur.

NOTICE

If flushing with water, do not leave water in sprayer for

extended periods. Flush again with Pump Armor and

leave protective coating in the sprayer to prevent freez-

ing or corrosion and to increase sprayer life.

ti30119a

ti27504a

ti30489a

ti30121a

ti30310a

ti30123a

«
...
18
19
20
21
22
...
»

Содержание LineLazer 3400













































Отзывы:

Нет отзывов