background image

308553ZAE

11

Operation

Pressure Relief Procedure

1.

Shut off the air to the pump.

2.

Open the dispensing valve, if used.

3.

Open the fluid drain valve to relieve all fluid pressure, 
having a container ready to catch the drainage.

Flush the Pump Before First Use

The pump was tested in water. If water could 
contaminate the fluid you are pumping, flush the pump 
thoroughly with a compatible solvent. Follow the steps 
under Starting and Adjusting the Pump.

Starting and Adjusting the Pump

1.

Be sure the pump is properly grounded. Read FIRE 
AND EXPLOSION HAZARD 
on page 3.

2.

Check all fittings to be sure they are tight. Be sure to 
use a compatible liquid thread sealant or PTFE tape 
on all male threads. Tighten the fluid inlet and outlet 
fittings snugly. Do not overtighten the fittings into the 
pump.

3.

Place the suction tube (if used) in the fluid to be 
pumped.

4.

Place the end of the fluid hose (N) into an appropriate 
container. Close the fluid drain valve (J).

5.

With the pump air regulator (H) closed, open all 
bleed-type master air valves (B, E).

6.

If the fluid hose has a dispensing device, hold it open 
while continuing with the following step. Slowly open 
the air regulator (H) until the pump starts to cycle. 
Allow the pump to cycle slowly until all air is pushed 
out of the lines and the pump is primed.

If you are flushing, run the pump long enough to 
thoroughly clean the pump and hoses. Close the air 
regulator. Remove the suction tube from the solvent 
and place it in the fluid to be pumped.

Pump Shutdown

At the end of the work shift, relieve the pressure.

WARNING

PRESSURIZED EQUIPMENT HAZARD

The system pressure must be manually relieved to 
prevent the system from starting or spraying 
accidentally. To reduce the risk of an injury from 
accidental spray from the gun, splashing fluid, or 
moving parts, follow the Pressure Relief Procedure 
whenever you

Are instructed to relieve the pressure

Stop spraying

Check or service any of the system equipment

Install or clean the spray tips

WARNING

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause 
serious injury or death if splashed in the 
eyes or on the skin, inhaled, or swallowed. 

Do not lift a pump under pressure. If dropped, the 
fluid section may rupture. Always follow thPressure 
Relief Procedure
 
above before lifting the pump.

WARNING

To reduce the risk of serious injury whenever you are 
instructed to relieve pressure, always follow the 
Pressure Relief Procedure at left.

Tel:  866-777-6060 
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com 

Int'l: +001 267 404 2910

Содержание Husky 307 F Series





































Отзывы: