background image

Installation 

8

312877S

Tips to Reduce Cavitation

Cavitation in a diaphragm pump is the 
formation and collapse of bubbles in the 
pumped liquid. Frequent or excessive 
cavitation can cause serious damage, 
including pitting and early wear of fluid 
chambers, balls, and seats. It may result in 
reduced efficiency of the pump. Cavitation 
damage and reduced efficiency both result in 
increased operating costs.

Cavitation depends on the vapor pressure of 
the pumped liquid, the system suction 
pressure, and the velocity pressure. It can be 
reduced by changing any of these factors.

1. Reduce vapor pressure: Decrease the 

temperature of the pumped liquid.

2. Increase suction pressure:

a. Lower the installed position of the pump 

relative to the liquid level in the supply.

b. Reduce the friction length of the suction 

piping. Remember that fittings add fric-
tion length to the piping. Reduce the 
number of fittings to reduce the friction 
length.

c. Increase the size of the suction piping.

d. Increase the Net Positive Suction Head 

(NPSH). See .

Performance Charts

page 23.

NOTE:

 Be sure the inlet fluid pressure 

does not exceed 25% of the outlet 
working pressure.

3. Reduce liquid velocity: Slow the cyclic rate 

of the pump.

Pumped liquid viscosity is also very important 
but normally is controlled by factors that are 
process dependent and cannot be changed to 
reduce cavitation. Viscous liquids are more 
difficult to pump and more prone to cavitation.

Graco recommends taking all of the above 
factors into account in system design. To 
maintain pump efficiency, supply only enough 
power to the pump to achieve the required 
flow.

Graco distributors can supply site specific 
suggestions to improve pump performance 
and reduce operating costs.

Содержание Husky 1050A



























Отзывы: