background image

Potential dangers from accidents during installation and use are divided into the following three 

categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect

Power

Ground

Be sure to do

WARNING:

 If the information in this manual is not followed exactly, a fire or explosion may result 

causing property damage, personal injury or death.

NORITZ AMERICA 

CORPORATION

 Installation Manual

CONDENSING TANKLESS GAS WATER HEATER

   NRC111OD (GQ-C3257WX US) 

 (Outdoor Installation)

DANGER indicates an imminently hazardous situation which, 

if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, 

if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, 

if not avoided, may result in minor or moderate injury.

DANGER

WARNING

CAUTION

Requests to Installers

•  In order to use the water heater safely, read this installation manual carefully, and follow the 

installation instructions.

•  Failures and damage caused by erroneous work or work not as instructed in this manual are not 

covered by the warranty.

•  Check that the installation was done properly in accordance with this Installation Manual upon  

completion.

•  After completing installation, please either place this Installation Manual in a plastic pouch and 

attach it to the side of the water heater (or the inside of the pipe cover or recess box if applicable), 

or hand it to the customer to retain for future reference.  Also, be sure to fill in all of the required 

items on the warranty and to hand the warranty to the customer along with the Owner's Guide.

CAUTION

*SBB80HT*

SBB80HT-2

Rev. 01/17

FOR USE IN RESIDENTIAL OR MANUFACTURED HOME APPLICATIONS.
Installation must conform with local codes, or in the absence of 

local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54- 

latest edition and/or the Natural Gas and Propane Installation 

Code CSA B149.1 - latest edition.
When applicable, installation must conform with the Manufactured 

Home Construction and Safety Standard, Title 24 CFR, Part 

3280  or  the  Canadian  Standard  CAN/CSA-Z240  MH  Mobile 

Homes, Series M86.
Noritz America reserves the right to discontinue, or change at any 

time, the designs and/or specifications of its products without notice.

CERTIFIED

R

Low NOx  Approved by SCAQMD

14 ng/J or 20 ppm

(Natural Gas Only)

Summary of Contents for NRC111OD






































Reviews: