Graco HEATED AIR SPRAY PACKAGE 237410 Скачать руководство пользователя страница 12

Страница: 12 / 17

Flushina

14.

15.

K E Y

Bleed-type master air valve

A i r l i n e

Fluid heater

6 a

Pump air regulator

6 b

Gun air regulator

3-way valve

1 3

Drain hose

4 4

Fluid regulator

4 5

F l u i d f i l t e r

4 8

Filter drain valve

For a first-time flush, trigger the gun, and circulate
the solvent for 20 seconds.

16.

For flushina after

fluid, turn the 3-way

valve to

Circulate.

Trigger the gun periodically

whiie circulating the solvent. Periodically

turn

the

3-way valve to

Drain

to flush out some dirty

vent. Flush until the system is clean. Repeat with
clean solvent, if necessary.

17.

18.

19.

Raise the suction

tube

out of the solvent, trigger

the gun, and run the pump until air comes from the
gun. Turn the 3-way valve to

Drain,

and run the

pump until all air is expelled.

20.

Release the trigger, and close the fluid regulator
(44) and the air regulators

Clean the filter screen, air cap, and fluid nozzle
separately.

Open the filter drain valve (48). Remove the filter
bowl, and reinstall the filter screen.

Thoroughly clean the inside and outside of the

suction

tube.

You are now ready to prime the system with

another fluid or to store the system.

Fig. 10

1 1

Содержание HEATED AIR SPRAY PACKAGE 237410


















Результаты поиска

Содержание HEATED AIR SPRAY PACKAGE 237410

Отзывы:

Похожие инструкции для HEATED AIR SPRAY PACKAGE 237410

Бренды по названию

Популярные бренды

Graco HEATED AIR SPRAY PACKAGE 237410, Инструкция по эксплуатации

Результаты поиска

Содержание HEATED AIR SPRAY PACKAGE 237410

Отзывы:

Похожие инструкции для HEATED AIR SPRAY PACKAGE 237410

Бренды по названию

Популярные бренды